AXTON ATC165S Kurulum ve Kullanım Kılavuzu - Sayfa 7
Araç Alıcısı AXTON ATC165S için çevrimiçi göz atın veya pdf Kurulum ve Kullanım Kılavuzu indirin. AXTON ATC165S 11 sayfaları. Component systems
CROSSOVER WIRING & MOUNTING
The crossover can be mounted in almost any location inside the vehicle. Recommended
places are: Inside the door, under the carpet in front of the door angles, under the dash-
board a.s.o. Just make sure not to install the crossover units where they may be exposed
to dirt or excessive moisture / water. Connect the tweeter wires and the main wires coming
from the amplifier or head unit to the crossover.
The woofers are either connected in parallel to the same channel or they get their own pair
of channels to be able to adjust the level to the tweeter even more precisely (bi-amping
mode).
Maintain polarities all the way – double check for correct connection. It is very important to
make sure that all the connections are electrically in phase, which means positive wire (+
or red) is connected to positive terminal, and negative wire (- or black) is connected to the
negative terminal. Reverse polarity connections of the tweeter will cause sharp sound and
a messed up front staging. If longer distances from the amplifier to the crossovers have to
be overcome, use good quality speaker cables with a minimum cross section of 2.5 mm².
Failure to do so will affect sound quality in a negative way.
X-OVER ADJUSTMENTS
All AXTON component set crossovers come with two adjustment options that allow you to
tailor the sound by setting slide switches on the pc board inside the housing, to compen-
sate for different mounting locations of the speaker units, as follows:
Tweeter level
As a general rule of thumb, the -3 dB position is best for tweeters that are mounted very
close to the listener's head like window triangles or top of the door panels.
The -0 dB position is usually the setting that provides a good tonal balance for most in-
stalls. It is recommended for the most tweeter positions.
Attention: The tweeter attenuation must be chosen identically on both crossovers. After
completing the settings of tweeter attenuation and polarity, you can mount the crossover
in place and reinstall all the other panels / factory grilles a.s.o. Your installation is now
complete and therefore ready, to be checked out.
Tip: The most pleasant tweeter level is found when the system plays very quietly. The
treble should then still be present, but not dominant.
TESTING THE INSTALLED SYSTEM
Slowly turn up the volume of your head unit and listen for distorted sounds. If everything
appears to be okay and it just sounds right, check out the speaker balance of the left and
right side by adjusting the balance control of your head unit. Shifting the balance to the left
channel should provide you with sounds coming solely from the left speaker system, while
shifting the balance to the right should do the same for the right speakers. If anything
appears to be wrong, you must recheck the wiring of the x-overs, the amp or the mid/
woofers.
– 12 –
TECHNICAL SPECIFICATIONS
ATC100S
Type
Component
Nominal Size
4" (10 cm)
Configuration / System
2-Way
Continuous Power Handling
60 W RMS
Crossover Slope LP Mid/Woofer
6dB / oct.
Crossover Slope HP Tweeter
6dB / oct.
Crossover Frequency
5000 Hz
Nominal Impedance
4 Ohms
Sensitivity
86 dB
Frequency Response (- 3dB)
90 Hz – 25 kHz
Mid Woofer
Basket (EURO-DIN)
4" (10 cm)
Mounting Depth
39 mm
Mounting Diameter
93 mm
Tweeter (with grill)
Overall Diameter
46 mm
Mounting Height (flat surface)
20 mm
Mounting Diameter (recessed)
42 mm
ATC130S-DVC
Type
Component
Nominal Size
5¼" (13 cm)
Configuration / System
2-Way
Continuous Power Handling
70 W RMS
Crossover Slope LP Mid/Woofer
6dB / oct.
Crossover Slope HP Tweeter
6dB / oct.
Crossover Frequency
5000 Hz
Nominal Impedance
2 x 4 Ohms
Sensitivity
87 dB
Frequency Response (- 3dB)
65 Hz–25 kHz
Mid Woofer
Basket (EURO-DIN)
5¼" (13 cm)
Mounting Depth
43 mm
Mounting Diameter
116 mm
Tweeter (with grill)
Overall Diameter
46 mm
Mounting Height (flat surface)
20 mm
Mounting Diameter (recessed)
42 mm
ATC130S
ATC165S
ATC200S
Component
Component
Component
5¼" (13 cm)
6½" (16.5 cm)
8" (20 cm)
2-Way
2-Way
2-Way
70 W RMS
90 W RMS
100 W RMS
6dB / oct.
6dB / oct.
6dB / oct.
6dB / oct.
6dB / oct.
6dB / oct.
5000 Hz
5000 Hz
5000 Hz
4 Ohms
4 Ohms
4 Ohms
88 dB
91 dB
92 dB
80 Hz–25 kHz
65 Hz – 25 kHz
60 Hz–25 kHz
5¼" (13 cm)
6½" (16.5 cm)
8" (20 cm)
43 mm
47 mm
57 mm
116 mm
145 mm
184 mm
46 mm
46 mm
46 mm
20 mm
20 mm
20 mm
42 mm
42 mm
42 mm
– 13 –