Axvue A1080DU Kullanım Kılavuzu

Bebek Monitörü Axvue A1080DU için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Axvue A1080DU 2 sayfaları. With 5.5" lcd screen & 2 cameras

Sayfayı Yazdır

INSTRUCTION MANUAL

AXVUE A1080DU VIDEO BABY MONITOR

WITH 5.5" LCD SCREEN & 2 CAMERAS

Please read the following instructions and warnings carefully

Keep this instruction manual for the future.

For technical support see the FAQ page.

For adult use only.

FEATURES & COMPONENTS

Camera:

1. Night-Vision LED

5. Power/Code

2. Lens

6. DC Jack

3. Microphone

7. Temperature Sensor

4. Speaker

8. Wall Mounting Hole

Monitor:

× 1

Model- A1080DU

Revised at 12/2020

Get to know us at: www.axvue.com

Keep the distance

between sensor and body

at least 0.6 inch for

accurate temperature

result.

0.6 in

1. LED*

2. Power/Video

3. Menu

4. Pan/Tilt

5. Zoom/Talk Back (OK)

6. Volume

7. Brightness

8. Cam/Split

9. VOX

10. Microphone

11. Speaker

12. DC Jack

13. Battery Compartment

14. Kickstand

*LED

Power & Low Battery

Sound Lights

Adapters:

× 3

× 2

WARNING

THIS PRODUCT CAN NOT SUBSTITUE PARENT'S SUPERVISION

ON YOUR CHILD.

-Store this product out of the reach of babies (at least 3 feets (0.9 m)

away from the crib). A strap wound around the baby's neck may result in

asphyxiation. Use a safety clip to clamp the power cord and keep it out

of baby's reach. Do not use other extension cords. Only use the power

adapter provided.

-Do not touch the exposed part if the adapter is connected with power.

-Test regularly before initial use or when change the position of camera.

-Avoid placing the product in humid place or contacting with liquid. (such as bathtub, sink, etc.)

-Do not apply heat to the product.(such as stoves, radiators, etc.)

-Using the product in ventilated place. Avoid placing it on sofas, cushions, beds or other places which

may block ventilation.

-The product only can be operated by adult. Do not allow baby to play with it. Tiny accessories are

contained, please be careful when unpack and install it.

BATTERY WARNING

-Only use the recommended rechargeable battery. Please contact us if you need to change it.

For the contact list, please refer to the last page of the instruction.

-Please clean the battery compartment before using it.

-Avoid short circuits the power supply terminal.

-Remove the battery when you are not using it or when running out of power.

-Keep the battery away from children.

-Dispose of the empty battery properly.

SETUP & USE

Please charge the battery for at least 8 hours before

using the product.

Step 1: Test reception ﬁrst, put the camera in a suitable place that

will provide you the best view of your baby in the crib (Note: Do

not hang up the camera ﬁrmly until the initial installation test is

completed). Plug the adapter into the wall outlet and turn on the

camera.

Step 2: Turn on the monitor by pressing and holding the Power/

Video"

" button for 5 seconds until "axvue" shows up, then the

video will show up on the screen immediately. If the video does

not show up, please refer to "TO PAIR MONITOR AND CAMERA

(ADD CAMERA)" on the next page. If the video shows up, the

initial installation test is completed, then you can set up the

camera according to the instruction below.

Set Up Camera: Place the camera on a ﬂat surface, such as a

wardrobe or shelf (Figure 1). Or hang it on the wall (Figure 2). No

matter wherever to place the camera, please make sure to keep it

away from the crib for at least 3 feet and all power cords should be

placed behind the camera properly. Then adjust the angle of the

camera lens until the entire crib shows up on the display, or adjust

it to the best angle that you think to watch your baby.

TO USE PLUGGED-IN MODE

Step 1: Place the monitor display in the living room, bedroom or any place you want to watch your

baby. Use an adapter to connect the camera with an electrical outlet.

Step 2: Turn on the monitor by pressing the Power/Video"

video shows up on the screen.

Step 3: Press Power/Video"

" button to turn oﬀ the video if you only need to hear the voice.

Step 4: Turn oﬀ the monitor completely by pressing and holding the Power/Video"

5 seconds.

TO USE PORTABLE/BATTERY MODE

Please charge the battery for 6 ~ 8 hours before using the product.

Step 1: Charge the battery for at least 8 hours before using portable/battery mode.

Step 2: Make sure the adapter is plugged into the camera.

Step 3: The battery life can be up to 10 hours if it is fully charged.

Battery life will be shortened if recharging it continuously. Unplug the power adapter when you are

not using it for a long time.

TO PAIR MONITOR AND CAMERA (ADD CAMERA)

The monitor and camera are paired before shipment. If it is unpaired for some reason, please refer

to the following steps:

Step 1: Make sure the camera and monitor are in the same place.

Step 2:

３

Make sure the power adapter is plugged into

camera and turn on the camera by pressing Power

On/Oﬀ Switch "

Step 3:

Step 4:

Step 5:

Red LED ﬂashs

Figure 1

3 feet

Figure 2

" button for 5 seconds until axvue logo or

" button for

" button for 3 seconds.

Turn on the monitor by pressing

and holding Power/Video"

button for 5 seconds.

Red LED stop ﬂashing

３