Axvue A242 Kullanım Kılavuzu

Bebek Monitörü Axvue A242 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Axvue A242 2 sayfaları. Video baby monitor with 4.3'' lcd screen and two cameras

Sayfayı Yazdır

INSTRUCTION MANUAL

AXVUE A242 Video Baby Monitor

with 4.3'' LCD Screen and Two Cameras

Please read the following instructions and warnings carefully

Tools required for wall mount: Screwdriver and drill (not included)

Keep this instruction manual for future reference.

For technical support see FAQ page.

For adult use only.

WARNING

THIS PRODUCT CAN NOT SUBSTITUE PARENT'S SUPERVISION ON YOUR CHILD.

- Store this product out of the reach of babies. (at least 1 meter away from the crib)

A strap wound around baby's neck may result in asphyxiation. Use safety clip to clamp the

power cord and keep it out of baby's reach. Do not use other extension cords. Only use the

AC adapter provided.

- Do not touch the exposed part if the adapter is connected with power.

- Test regularly before initial use or when change the position of camera.

- Avoid placing the product in humid place or contacting with liquid. (such as bathtub, sink,

etc.)

- Do not apply heat to the product.(such as stoves, radiators, etc.)

- Using the product in ventilated place. Avoid placing it on sofas, cushions, beds or other

places which may block ventilation.

- The product only can be operated by adult. Do not allow baby to play with it. Tiny

accessories are contained, please be careful when unpack and install it.

BATTERY WARNING

- Only use the recommended rechargeable battery. Please contact with us if you need to

change it. For contact list, please refer to the last page of the instruction.

- Please clean the battery container before using.

- Avoid short circuit at power supply terminal.

- Remove the battery when you are not using it or when running out of power.

- Keep battery away from children.

- Dispose the empty battery properly.

WARNING:

Asphyxiation Danger: Store this product out of the reach of babies (at least 3 feet away from

the crib). A strap wound around baby's neck may result in asphyxiation. Use safety clip to

clamp the power cord and keep it out of baby's reach. Do not use other extension cords. Only

use the AC adapter provided.

Features and components

MONITOR

VOX

*LED

Power & Low Battery

Sound Lights

VOX

Model- A242

Revised at 7/2020

VOX

Get to know us at: www.axvue.com

1 LED*

2 Power / Menu

3 Talk Back

4 Volume Up

5 Volume Down

6 To Select a Camera / Up

7 Auto-scan / Down

8 Zoom / Left

9 VOX / Right

10 Microphone

11 Speaker

12 Battery Compartment

13 Kickstand

14 Video On / Oﬀ

15 DC Jack

Adapter for monitor:

VOX

Features and components

CAMERA

1 Power Indicator

2 Lens

3 Nighttime LEDs

4 Microphone

5 DC Jack

x12

6 Wall mounting hole

7 Speaker

8 Power On / Oﬀ Switch

Wall mount kits

Setup & Use

Please charge the battery for at least 8 hours before using the product.

Step 1: Test reception ﬁrst, put camera in a suitable place that

will provide you the best view of your baby in the crib (Note: Do

not hang up the camera ﬁrmly until initial installation test is

completed). Plug adapter into wall outlet and turn on the

camera.

Step 2: Turn on monitor by pressing and holding

button for 5 seconds until "axvue" shows up, then video will

show up on the screen immediately. If video does not show up,

please refer to "TO PAIR MONITOR AND CAMERA (ADD

CAMERA)" at next page. If video shows up, the initial installation

test is completed, then you can set up the camera according to

the instruction below.

Set Up Camera: Place camera on a ﬂat surface, such as wardrobe

or shelf (Figure 1). Or hang it on the wall (Figure 2). No matter

wherever to place the camera, please make sure to keep it away

from the crib for at least 3 feet and all power cords should be

placed behind the camera properly. Then adjust the angle of

camera lens until the entire crib shows up on the display, or

adjust it to the best angle that you think to watch your baby.

Wall Mounting Steps

1. Pre-drill a hole with 3/16" (4.8mm) aperture in the wall.

2. Insert wall anchor into the hole and hammer it until it is ﬂat with the wall.

3. Tighten the screw until 1/4" (6.2mm) of the screw is exposed.

4. Insert the adapter into camera's DC Jack.

5. Slide the bottom of camera down onto the screw until it can hang on the wall ﬁrmly.

6. Plug adapter into an electrical outlet.

7. Use safety clip to clamp the power cord and keep it out of baby's reach.

TO USE PLUGGED-IN MODE

Step 1: Place the monitor display in living room, bedroom or any place you want to watch your baby.

Use adapter to connect camera with electrical outlet.

Step 2: Turn on monitor by pressing POWER/MENU

shows up on the screen.

Step 3: Press VIDEO ON/OFF

button to turn oﬀ the video if you only need to hear the voice.

Step 4: Turn oﬀ the monitor completely by pressing and holding POWER/MENU

TO USE PORTABLE / BATTERY MODE

Please charge the battery for 6~8 hours before using the product.

Step 1: Charge the battery for at least 8 hours before using portable/battery mode.

Step 2: Make sure the adapter is plugged into camera.

Step 3: The battery life can be up to 16 hours if it is fully charged.

Battery life will be shortened if recharging it continuously. Unplug the AC adapter when you

are not using it for a long time.

TO PAIR MONITOR AND CAMERA (ADD CAMERA)

The monitor and camera are paired before shipment. If it is unpaired for some reason,

please refer to the following steps:

Step 1: Make sure the camera and monitor are in the same space.

Step 2:

Step 3:

５ｓ

VOX

Step 4:

VOX

(continued)

Adapter for camera:

Figure 1

Power / Menu

3 feet

Figure 2

button for 5 seconds until AXVUE logo or video

button for 5 seconds.

Make sure the AC adapter is plugged into

camera and turn on the camera by pressing

５ｓ

POWER/CODE

button for 5 seconds.

Turn on monitor by pressing

and holding POWER/MENU

Signal

button for 5 seconds.

VOX

vox

VOX