Epson 1680 - Expression Special Edition Ürün Destek Bülteni - Sayfa 4

Yazıcı Epson 1680 - Expression Special Edition için çevrimiçi göz atın veya pdf Ürün Destek Bülteni indirin. Epson 1680 - Expression Special Edition 5 sayfaları. Color image, expression series
Ayrıca Epson 1680 - Expression Special Edition için: Kullanıcı Kılavuzu (7 sayfalar), Broşür ve Teknik Özellikler (24 sayfalar), Ürün Bilgileri (9 sayfalar), Buradan başlayın (4 sayfalar), Teknik Özellikler (2 sayfalar), Ürün Destek Bülteni (23 sayfalar), Manuel (11 sayfalar), Güncelleme (1 sayfalar), Ürün Destek Bülteni (40 sayfalar), Ürün Destek Bülteni (17 sayfalar), Ürün Destek Bülteni (3 sayfalar), Ürün Destek Bülteni (24 sayfalar), Garanti (2 sayfalar), Ürün Destek Bülteni (29 sayfalar), Ürün Destek Bülteni (8 sayfalar), Ürün Destek Bülteni (3 sayfalar), Ürün Destek Bülteni (14 sayfalar), Ürün Destek Bülteni (1 sayfalar), Ürün Destek Bülteni (18 sayfalar), Ürün Destek Bülteni (12 sayfalar), Ürün Destek Bülteni (40 sayfalar), Ürün Destek Bülteni (11 sayfalar), Ürün Destek Bülteni (40 sayfalar), Ürün Destek Bülteni (22 sayfalar), Ürün Destek Bülteni (12 sayfalar), Ürün Destek Bülteni (21 sayfalar), Manuel (24 sayfalar)

NOTE:

This document assumes that you are using an Adaptec card. The AHA1510 and

AHA1540C were tested when creating this document.

Once you have verified that the above lines are in the CONFIG.SYS, shut down

OS/2 and reboot.

NOTE:

If the SCSI card does not find any devices on the SCSI chain, the AHAxxxx.ADD

driver will not load thus causing VASPI.SYS not to load. If this occurs, double

check your card's configuration and the SCSI cabling.

Epson TWAIN ~1.0~

Follow the steps below to enable Epson TWAIN ~1.0~:

From the OS/2 desktop, double click on the OS/2 SYSTEM folder

Double click on the COMMAND PROMPTS folder

Double click on the Win-OS/2 icon.

Once Windows is loaded, follow the TWAIN installation procedure. When the

installation program asks if you wish to make changes to the CONFIG.SYS or

the CONFlG.ADD, select CONFIG.ADD.

Once the installation has completed, exit Windows.

If the COMMAND PROMPTS folder is not open, follow steps 1 and 2.

Move the mouse to the WIN-OS/2 FULL SCREEN icon. Click on the right

mouse button.

Select SETTINGS from the pop-up menu.

Once the SETTINGS notebook has opened, click on SESSION.

10.

Click on the WIN-OS2 SETTINGS.

11.

Click on OTHER DOS SETTINGS.

12.

Click on OK.

13.

Highlight DOS-DEVICE.

14.

In the window to the right, add the EPSN.SYS driver. X represents the

appropriate SCSI ID of the scanner.

The device line would be entered in the following manner.

C:\EPSN.SYS 3 /Sx /i79

PSB No: P-0103A

Page: 3 of 4