Axxess AX-BM90122 Kurulum Talimatları - Sayfa 3

Kayıt Ekipmanları Axxess AX-BM90122 için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. Axxess AX-BM90122 4 sayfaları. Bmw (with m.o.s.t. 25 amplifier) 2004-2013

Sayfayı Yazdır

INSTALLING THE AX-BM90122 INTERFACE

With the key in the off position:

• Connect the AX-BM90122 harness to the AX-BM90122 interface.

• Connect the AX-BM90122 harness to the AX-BM90122 amplifier interface.

• Remove the dust cover from fiber optic port in the AX-BM90122 amplifier interface.

• Connect the factory fiber optic cable into the AX-BM90122 amplifier interface.

• Connect the AX-BM90122 harness to the wiring harness in the vehicle.

• Connect the ASWC-1 harness to the ASWC-1 interface, and then to the AX-BM90122 interface.

PROGRAMMING THE ASWC-1 INTERFACE

• Press and hold the Volume-Up button on the steering wheel.

• Turn the ignition on, the L.E.D. in the ASWC-1 interface will start flashing rapidly, which

means the ASWC-1 is looking for the vehicle and the radio.

Note: If the L.E.D. did not start flashing rapidly, press the reset button for 3 seconds, while

still holding the Volume-Up button.

• After a few seconds the L.E.D. should stop flashing rapidly, and then go out for

approximately 2 seconds.

• After approximately 2 seconds there will be a series of 7 Green flashes, some short, and

some long. The long flashes represent the wires that are connected to the ASWC-1. The 3rd,

4th, 5th, and 6th flashes should be longer.

Tip: Knowing this will help to troubleshoot, if need be.

• The L.E.D. will pause for another 2 seconds, and then flash Red up to 18 times depending on

which radio is connected to the ASWC-1. Refer to the L.E.D. feedback section for information.

• This is the end of the auto detection stage. Release from holding the Volume-Up button.

If the ASWC-1 detected the vehicle and the radio successfully, the L.E.D. will light up solid.

• Test the steering wheel controls for proper operation. Refer to the ASWC-1 instructions online at

axxessinterfaces.com for customizing the buttons, if so desired.

PROGRAMMING THE

ASWC-1 INTERFACE

L.E.D. feedback

The (18) Red L.E.D. flashes represent which brand radio the ASWC-1 is connected to. Each

flash represents a different radio manufacturer. For example, if you are installing a JVC radio,

the ASWC-1 will flash Red (5) times, and then stop. Following is a legend that dictates which

radio manufacturer corresponds to which flash.

L.E.D. feedback legend

1 flash - Eclipse (Type 1) †

2 flashes - Kenwood ‡

3 flashes - Clarion (Type 1) †

4 flashes - Sony / Dual

5 flashes - JVC

6 flashes - Pioneer / Jensen

7 flashes - Alpine *

8 flashes - Visteon

9 flashes - Valor

* Note: If the ASWC-1 flashes Red (7) times, and you do not have an Alpine radio connected to

it, that means the ASWC-1 does not detect a radio connected it. Verify that the 3.5mm jack is

connected to the correct steering wheel jack/wire in the radio.

** Note: The AX-SWC-PARROT is required (sold separately). Also, the Parrot radio must be updated

to rev. 2.1.4 or higher through www.parrot.com.

† Note:

If you have a Clarion radio and the steering wheel controls do not work, change the radio type to

the other Clarion radio type; same for Eclipse. Refer to the "Programming Information" document online

‡ Note: If you have a Kenwood radio and the L.E.D. feedback comes back as showing as a JVC radio,

change the radio type to a Kenwood. Refer to the "Programming Information" document online.

(CONT.)

10 flashes - Clarion (Type 2) †

11 flashes - Metra OE

12 flashes - Eclipse (Type 2) †

13 flashes - LG

14 flashes - Parrot **

15 flashes - XITE

16 flashes - Philips

17 flashes - TBD

18 flashes - JBL

REV. 5/8/2018 INSTAX-BM90122