Epson C380045HA - Stylus Color 980 Inkjet Printer Ürün Bilgi Kılavuzu - Sayfa 11
Yazıcı Epson C380045HA - Stylus Color 980 Inkjet Printer için çevrimiçi göz atın veya pdf Ürün Bilgi Kılavuzu indirin. Epson C380045HA - Stylus Color 980 Inkjet Printer 14 sayfaları. Windows printer software does not install
Ayrıca Epson C380045HA - Stylus Color 980 Inkjet Printer için: Şartname Sayfası (2 sayfalar), Hızlı Başlangıç (2 sayfalar), Şartname (2 sayfalar), Sorun Giderme Kılavuzu (1 sayfalar)
Sayfayı Yazdır
Using the Head Cleaning Utility
Follow these steps to run the Head Cleaning utility:
1. Make sure the printer is turned on but not printing, and
both the B black and A color ink out lights are off.
2. Access the printer settings dialog box.
3. Click the
tab (Windows) or the
Utility
(Macintosh).
4. On the Utility menu, click the
5. Follow the instructions on the screen to clean the print
head. Cleaning takes about 30 seconds, during which the
printer makes some noise and the P power light flashes.
Never turn off the printer while the P power light is
flashing, unless the printer hasn't moved or made noise
for more than 5 minutes.
6. When the P power light stops flashing, run a nozzle check
to test the results and reset the cleaning cycle.
Make sure paper is loaded in the printer and click
(Windows) or
nozzle check pattern
(Macintosh). Then click
prints; see "Examining the Nozzle Check Pattern" on
page 11 for details.
7. If the nozzle check pattern is filled in completely, click
.
Finish
If the pattern has any gaps, click
again. If you don't see any improvement after cleaning two or
three times, try the suggestions in "Problems and Solutions" in
the Printer Basics book or "Troubleshooting" in the electronic
EPSON Stylus COLOR 980 Reference Guide.
Using the Control Panel
Follow these steps to clean the print head:
1. Make sure the printer is turned on but not printing, and
both the B black and A color ink out lights are off.
2. Press the R cleaning button and hold it down for three
seconds. Cleaning takes about 30 seconds, during which the
printer makes some noise and the P power light flashes.
Never turn off the printer while the P power light is
flashing, unless the printer hasn't moved or made noise
for more than 5 minutes.
3. After the P power light stops flashing, print a page to test
the print quality and reset the cleaning cycle.
If you're connected directly to the printer, run a nozzle
check. Go to step 4.
If you're using DOS or printing over a network, open an
application and print a document containing black and
color data. Then go to step 8.
Utility icon
button.
Head Cleaning
Print
Confirmation
. The nozzle check pattern
Next
to clean the print head
Clean
4. Start an application, open a document, and access the
printer settings dialog box.
5. Click the
tab (Windows) or the
Utility
(Macintosh). You see the Utility menu.
6. Make sure paper is loaded in the printer, click the
button, and click
Check
prints on the printer; see "Examining the Nozzle Check
Pattern" on page 11 for details.
7. If the nozzle check pattern is filled in completely, click
.
Finish
If the pattern has any gaps, click
head again.
8. If you don't see any improvement after cleaning two or
three times, try the suggestions in "Problems and Solutions"
in the Printer Basics book or "Troubleshooting" in the
electronic EPSON Stylus COLOR 980 Reference Guide.
Examining the Nozzle Check Pattern
Examine the nozzle check pattern you print. It should look
something like this:
Each staggered horizontal and straight vertical line should be
complete, with no gaps in the dot pattern. If your printout
looks okay, you're done. If there are gaps in the lines, as shown
below, clean the print head again; see page 10 for instructions.
gaps in pattern
8/00
EPSON Stylus COLOR 980
Utility button
. The nozzle check pattern
Next
to clean the print
Clean
gaps in pattern
EPSON Stylus COLOR 980
Nozzle
- 11