CREE LIGHTING L4-22 Kurulum Talimatları - Sayfa 2
Aydınlatma Ekipmanları CREE LIGHTING L4-22 için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. CREE LIGHTING L4-22 2 sayfaları. Led flat panel
Sayfayı YazdırThe ìnstaIIatìon must be further than 20 cm from an inflammable product.
WARNING: In order to prevent the risk of an electric shock, injury or fire when using electric ap-
Cut the mains power supply before any work.
pliances, read and follow the basic safety instructions below:
All damaged power cables must be replaced by qualified person.
2/ Note before installation
The ìnstaIIatìon must be made by a qualified person.
Check the contents of the pack before installing.
Mechanically or electrically altering the light is prohibited.
The ìnstaIIatìon must be further than 20 cm from an inflammable product.
WARNING: In order to prevent the risk of an electric shock, injury or fire when using electric ap- pliances,
This light is not compatible with dimmers.
Cut the mains power supply before any work.
read and follow the basic safety instructions below:
If, when unpacked, the item includes plastic bags, they must not be left within the reach of children due
All damaged power cables must be replaced by qualified person.
The ìnstaIIatìon must be made by a qualified person.
to the risk of suffocation.
Mechanically or electrically altering the light is prohibited.
The ìnstaIIatìon must be further than 20 cm from an inflammable product.
Do not install or operate a damaged light or a light with missing parts.
This light is not compatible with dimmers.
Cut the mains power supply before any work.
Make sure you only connect your light when the installation is complete.
All damaged power cables must be replaced by qualified person.
If, when unpacked, the item includes plastic bags, they must not be left within the reach of children due
Do not use the DRIVER for a lamp other than the LED panel.
to the risk of suffocation.
Mechanically or electrically altering the light is prohibited.
This light is not compatible with dimmers.
Do not install or operate a damaged light or a light with missing parts.
If, when unpacked, the item includes plastic bags, they must not be left within the reach of children
Make sure you only connect your light when the installation is complete.
due to the risk of suffocation.
Do not use the DRIVER for a lamp other than the LED panel.
3.1/ Recessed Installation
Do not install or operate a damaged light or a light with missing parts.
Make sure you only connect your light when the installation is complete.
Do not use the DRIVER for a lamp other than the LED panel.
3.1/ Recessed Installation
3.2/ Suspended Installation
3.2/ Suspended Installation
5
5
See Figure A -
Electrical
connections
See Figure A -
See Figure A -
Electrical
connections
See Figure A -
Electrical
connections
*
*
2. Assemble the frame
1.Accessories bag
3.3/ Surface Installation
3.3/ Surface Installation
2. Assemble the frame
1.Accessories bag
4.Remove one side of the frame
3. Use the wall plugs to install the frame
4.Remove one side of the frame
3. Use the wall plugs to install the frame
4.Remove one side of the frame
3. Use the wall plugs to install the frame
5.Connect the driver with the power source (see Figure A - Electrical connections) and insert the led panel in
the frame - Close the frame.
5.Connect the driver with the power source (see Figure A - Electrical connections) and insert the led panel in
the frame - Close the frame.
5.Connect the driver with the power source (see Figure A - Electrical connections) and insert the led panel in
the frame - Close the frame.
4/ Electrical connection
4.1/
Connect the live and the neutral from the 230V circuit to the driver's live and neutral using a terminal
block (not included).
4.2/
Connect the driver's male jack to the LED panel female jack.
4/ Electrical connection
FIGURE A
4.1/
Connect the live and the neutral from the 230V circuit to the driver's live and neutral using a terminal
4/ Electrical connection
4/ Electrical connection
block (not included).
4.1/ Connect the live and the neutral from the 230V circuit to the driver's live and neutral
4.1/
4.2/
using a terminal block (not included).
Connect the live and the neutral from the 230V circuit to the driver's live and neutral using a terminal
4.2/ Connect the driver's male jack to the LED panel female jack.
Connect the driver's male jack to the LED panel female jack.
block (not included).
FIGURE A
4.2/
Connect the driver's male jack to the LED panel female jack.
FIGURE A
Note: in some cases the live wire may be red or black.
5/ Care:
The light should be cleaned regularly by dusting it or using a damp wipe.
The light source on this light is not repleaceable: when the light source reaches the end of its service
life, the entire appliance must be repleaced.
Note: in some cases the live wire may be red or black.
5/ Care:
The light should be cleaned regularly by dusting it or using a damp wipe.
The light source on this light is not repleaceable: when the light source reaches the end of its service life,
Note: in some cases the live wire may be red or black.
5/ Care:
the entire appliance must be repleaced.
The light should be cleaned regularly by dusting it or using a damp wipe.
The light source on this light is not repleaceable: when the light source reaches the end of its service
life, the entire appliance must be repleaced.
5/ Care:
The light should be cleaned regularly by dusting it or using a damp wipe.