Cres Cor CO151FUA12 Kurulum, Kullanım ve Bakım Kılavuzu - Sayfa 4

Konveksiyonlu Fırın Cres Cor CO151FUA12 için çevrimiçi göz atın veya pdf Kurulum, Kullanım ve Bakım Kılavuzu indirin. Cres Cor CO151FUA12 10 sayfaları. Cres cor inc. convection and retherm ovens installation, operation and maintenance manual

Sayfayı Yazdır
FL-2202-MP-M
Ovens
Rev. 1 (4/08)
POWER SWITCH
ON
OFF
POWER
HOW TO START UNIT:
(for fi rst-time operation only)
A new oven needs to "burn off" factory oils and glue
before it's fi rst use. Do NOT load food into oven until this
has been done!
1.
Push power switch to "ON".
2.
Press the SELECT button and choose the TIMED
mode.
3.
Press the COOK BUTTON and set the temperature to
350° F (177° C).
4.
Press the HOLD button and set the temperature to
150° F (66° C).
5.
Press the PROBE/TEMP button and set the time to 1
hour.
6.
Open upper door and move thumb screw on cabinet to
open the cabinet vent.
7.
Allow oven to run automatically for one hour of
COOK/RETHERM cycle and 30 minutes of HOLD
cycle.
HOW TO SET CONTROL:
FOR TIMED COOK OPERATION
Press the SELECT button to choose the Timed mode.
COOKING TIME
1.
Press the PROBE/TIME button. The display will
show the cook/retherm time.
2.
Use the UP and DOWN arrows to set the desired
time.
3.
Press the SET Button to enter the time into the
control.
COOKING TEMPERATURE
1.
Press the COOK button and the display wil show the
cook/retherm temperature.
2.
Use the UP and DOWN arrows to set the desired
temperature.
Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com
Page 4 of 10

OPERATING INSTRUCTIONS

PRODUCT KEYS
Figure 1: Control Panel
(For parts description, refer to page 8.)
5925 Heisley Road • Mentor, OH 44060-1833
MODE
PROBE
SELECT
3.
Press the SET button to enter the temperature into the
control.
NOTE: Press the OVEN TEMP button at any time to
view the actual oven temperature.
HOLDING TEMPERATURE
1.
Press the HOLD button and the display will show the
holding temperature.
2.
Use the UP and DOWN buttons to set the desired
temperature.
3.
Press the SET button to enter the temperature into the
control.
Press the START button and the display shows the
remaining time in the cook/retherm cycle.
NOTE: The control will beep after it times down to zero
and then automatically switches to the Hold mode. The
display will then show the hold setpoint temperature.
FOR PROBE COOK OPERATION
Press the SELECT button to choose the probe mode.
PROBE TEMPERATURE
1.
Press the PROBE/TIME button and the display will
show the probe setpoint temperature.
2.
Use the UP and DOWN arrows to set the desired
temperature.
3.
Press the SET button to enter the temperature into the
control.
NOTE: Press the OVEN TEMP button at any time to
view the actual oven temperature.
Press the START button and the display will show the
actual probe temperature.
NOTE: The control will beep when the probe setpoint
temperature has been reached and then automatically
switches to the Hold mode. The display will then show
the hold setpoint temperature.
CONTROL
SETPOINTS
TIME - TEMPERATURE
RETHERM
COOK
TIMED
TIME
SET
HEAT
COOK
HOLD
PROBE
OVEN
START
STOP
HOLD
TEMP