FIAMA EP7 Kullanıcı Kılavuzu - Sayfa 5
Ölçüm Cihazları FIAMA EP7 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. FIAMA EP7 8 sayfaları. Battery-powered electronic position indicator
Sayfayı Yazdır
EP7
Reset: reset function of the displayed value; after pressing
set to zero.
Preset: preset function of the displayed value; after pressing
becomes equal to the value in the
(when the digit on the right is set to 2).
Fast Preset: the fast setting of the displayed value on the display; after pressing
appears and pressing 2 times
and then confirm with
corrected often.
Origin change (correction of the displayed value for tool changes): with this function 3 different
origins (0,1,2) can be set and with
After setting 4 in the first digit on the right of the
pressing 2 times
ENTER
radius of cutter 0), which is then confirmed by pressing
Now
will appear which is the nominal value for tool 1 (for example the radius of cutter 1): set
the correct value and confirm with
Finally
will appear which is the nominal value for tool 2 (for example the radius of cutter 2):
set the correct value and confirm with
In practice
,
which are used.
As a special case, if
origin 2 respectively.
/
function: Enables passing from an absolute to relative value; after pressing
ABS
REL
displayed value is temporarily set to zero to measure a relative motion of the shaft. On the display
the
icon indicates that the current display is relative to the reference point that has just been
REL
created. Pressing again
mm/inch conversion: Pressing
back. When in inch mode, the
decimal place. When the parameter
Offset: This parameter is added to or subtracted from the displayed value to correct it in case, for
example, of a tool change or to compensate tool wear. After setting a positive offset value, the
displayed value will be the measured value plus the offset value. After setting a negative offset
value, the displayed value will be the measured value minus the offset value.
Fast Offset: After pressing
it is possible to set directly the value to be displayed (use buttons
/
). This function is useful if it is necessary to correct often the displayed value.
ENTER
RESET
Counting direction
It sets the counting direction, allowed values 0 or 1.
By setting 0, the displayed value increases turning the shaft clockwise.
By setting 1, the displayed value decreases turning the hollow shaft clockwise.
Adjustment of displayed value
After the installation of instrument on the machine and setting of all parameters, in order to visualize
on the display the correct value it is necessary to carry out the reset or preset.
Position the shaft in a point in which the correct measure that has to be visualized is known exactly
(for example the stroke end point) or measure the position in that point of the shaft. Program
parameter
with value 3 in the first digit on the right and exit programming.
Date: 13/01/16
parameter, which can be set immediately after
/
ENTER
RESET
/
). This function is useful when the displayed value must be
ENTER
RESET
/
ENTER
RESET
/
it is possible to set the nominal value for tool 0 (for example the
RESET
/
ENTER
RESET
ENTER
, and
are the nominal values associated to the three different tools
is set to zero,
causes the absolute value to be displayed and the
converts the measurement from millimeters to inches and
icon will appear and the displayed value will have an additional
INCH
=4 the mm/inch conversion is not available.
/
,
ENTER
RESET
File: EP7_ing_rev1.7.doc
ENTER
ENTER
it is possible to set the value directly (use
it is possible to switch from one origin to another.
parameter,
/
ENTER
RESET
.
/
.
RESET
and
are the values to display in origin 1 and in
appears and by pressing two times
Electronic position indicator
/
, the displayed value is
RESET
/
, the displayed value
RESET
ENTER
will appear and after
.
icon will appear.
ABS
ENTER
and confirm with
/
RESET
and
, the
/
RESET
Page: 5/8