Accusplit Eagle AE170XLG Kullanım Talimatları - Sayfa 4

Adımsayar Accusplit Eagle AE170XLG için çevrimiçi göz atın veya pdf Kullanım Talimatları indirin. Accusplit Eagle AE170XLG 5 sayfaları. Accusplit pedometer operating instructions

Sayfayı Yazdır

Accusplit Eagle AE170XLG Kullanım Talimatları

VIEWING YOUR RESULTS

Once you put on your pedometer with the cover closed, it

will automatically begin to record your steps, activity time,

distance, and calories burned. Repeatedly press the MODE

button to cycle through the pedometer modes:

STEPS g T IME g DISTANCE g CALORIE g STEPS

Time, Distance, and Calories are counted automatically

whenever steps are being counted.

• TIME is time spent in step activity.

• DISTANCE is simply stride length x steps.

• CALORIES is calorie burn from activity based on

your weight and rate of stepping pace.

Note: For extra accuracy, the default Step Filter Setting is 1.

See page 28 to learn more.

RESETTING YOUR PEDOMETER

Most people prefer to reset counts daily. T o reset your

regular counts: From STEP , T IME, DISTANCE, or CALORIE

mode, press and hold the yellow RESET button for at least 2

seconds. Y ou'll see the values all go back to zero.

CHANGING STEP FILTER SETTING

While the JW200 PedometerEngine™ Step Sensor is

extremely accurate, some people like to have the ability to

filter out false steps. T herefore, the unit has a variable setting

step filter, to allow fine-tuning to your specific preferences.

You can set the value to any value from 0 – 5 steps. For

example, if the filter is set to "3" , the unit will wait to start

counting steps until more than three steps have been taken in

less than five seconds.

Press S3+ (MODE) or S3– (RESET) to change the Step Filter

Setting.

CHANGING UNITS (English vs. Metric)

The Pedometer can display either in English units (inches,

miles, and pounds - this is the default), or in Metric units

(cm, km, and kg). From within Deep Set mode (see above),

press the S2 (SET) button to cycle back and forth between

setting the Step Filter set point and Choice of Unit System.

The unit will show either "US" or "EU" (for European Union)

depending on the unit system chosen. If you change units

after using the pedometer, the unit will convert all of your

data into the new unit system when you exit Deep Set model.

You can check to see which system of units you are using by

seeing which measurement units are displayed on the Stride

and Weight setting screens.

GOAL TRACKING

As discussed in beginning of instructions, this unit keeps

track of your progress towards the Step, T ime, Distance, and

Calorie goals you set. Progress is shown as a series of small

bars appearing on the bottom of the display, with each bar

representing 5% of the total. For example, if you set your step

goal to 4,000 steps, and you've walked 2,000 steps so far,

the goal indicator in STEP mode will show as 50% complete.

Progress towards each goal is shown on the corresponding

screen – for example, when viewing DIST, you will see both

the distance traveled in numbers, and also the progress

towards your distance goal on the bottom of the display.

OTHER SETTINGS

The Step Filter and Unit of Measurement settings are

accessed through a special "deep set" mode.

To enter this mode, press and hold the S1 (SET) button for 4

seconds. T he screen will display a single digit. From within

Deep Set mode, press the S2 (SET) button to cycle back and

forth between the Step Filter set point and Choice of Unit

System.

Can be set

IGI

from 0-5

STEP TIME

steps

170

JW200

S3-

Set Step Filter set point

Press S3+ (MODE) or S3– (RESET) to change the

Measurement Mode. Press and hold S4 (SET) for 2 seconds to

exit Deep Set Mode (See page 21).

Note: T he unit will save any changes and exit set mode after

30 seconds unattended.

"US" (English)

or "EU" (Metric)

170

JW200

Set Measurement Mode

ALKER

.COM

DIST CAL

SET

CALORIE

100%

S1,S2,S4

S3+

IGI