Fibar Group FGR221 Kullanım Kılavuzu

Kontrolör Fibar Group FGR221 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Fibar Group FGR221 2 sayfaları. Roller shutter controller

Sayfayı Yazdır

ENG

I GENERAL INFORMATION ABOUT FIBARO SYSTEM

FIBARO is a wireless system, based on Z-Wave technology.

FIBARO provides many advantages when compared to similar

systems. In general, radio systems create a direct connection

between the receiver and transmitter. But the radio signal is

weakened by various obstacles located on its path (apartment walls,

furniture, etc.) and in extreme cases it fails to transfer required data.

The advantage of FIBARO system is that its devices apart from

being transmitters and receivers of signals, they are also a signal

"duplicators". When a direct connection path between the transmitter

and the receiver can not be established, the connection may be

achieved through other intermediate devices.

OPERATING MANUAL

FIBARO is a bi-directional wireless system. It means that the signal

ROLLER SHUTTER CONTROLLER

is not only sent to the receivers but also the receivers send the

confirmation of its reception. This operation confirms their status so

FGR221 v1.4

to check whether they are active. Safety of the FIBARO system

transmission is comparable to the safety of transmission in data bus

wired systems.

FIBARO operates in the free band for data transmission at 868MHz

Remotely controlled Roller Shutter Controller of FIBARO system is

frequency. Every FIBARO system has its own unique identification

designed to control motors of roller shutters, awnings, etc.

number (home ID). Therefore, it is possible to operate two or more

independent systems in one building without any interference.

It has the function of detecting the current state of a controlled

device, e.g. position of roller shutter.

Although Z-Wave is quite new technology, it has already become

recognizable and officially binding standard, similarly to Wi-Fi. Many

manufacturers in various industries offer solutions based on Z-Wave

technology, guaranteeing their compatibility. This means that the

Specifications

system is open and it may be extended in the future. Find more

information at www.fibaro.com.

FIBARO generates a dynamic network structure. After FIBARO

Power supply

110 - 230 V ±10% 50/60Hz

system is switched on, the location of its individual components is

Power of supplied motor

up to 1kW

automatically updated in real-time through status confirmation

signals received from devices operating in a "mesh" network.

In accordance with EU

EN 55022

standards

EN 61000

The in-wall Roller Shutter Controller is hereinafter referred to as

Fibaro Roller Controller. It is designed to switch rise/lower roller

shutter connected to its terminals using radio waves, controllers and

Temperature limits

105 °C

a push button directly connected to Fibaro Roller Controller.

Operational temperature

0 - 40 °C

For installation in boxes

Ø ≥ 50mm

II Assembling Roller Shutter Controller

Radio protocol

Z-Wave

Radio Frequency

868 MHz

Range

up to 50 m outdoors

up to 30 m indoors

(depending on building materials)

Dimensions (H x W x D)

15 x 42 x 36 mm

1. Before installation ensure that the voltage supply is

Technical Information

disconnected.

2. Connect the Roller Shutter Controller in accordance with the

diagram on Fig. 1

3. Place the device in the electrical box.

• Controlled by FIBARO system devices or any Z-Wave controller.

4. Arrange the antenna (tips are presented below diagrams of

fig. 1)

• Microprocessor control

• Executive elements: relays.

• The device may be operated by mono-stable and bi-stable

push-buttons and by push-buttons dedicated for roller shutters.

DANGER

Danger of electrocution! All works on the device

may be performed only by a qualified and licensed

electrician. Observe national regulations.

DANGER

Danger of electrocution. Even when the device is

turned off, voltage may be present at its terminals.

Any

works

introducing

changes

into

the

configuration of connections or the load must be

always

performed

with

disconnected

voltage

(disable the fuse).

Fig.1 Circuit diagrams for the Roller Shutter Controller

TIPS

• Do not connect the device to loads exceeding

recommended values.

NOTES FOR THE DIAGRAM:

• Connect only in accordance with the diagram

L - live lead

presented in the manual. Improper connections may

N - neutral lead

be dangerous.

S1 - terminal for key no. 1 (has the option of entering the device in

self-learning mode)

S2 - terminal for key No. 2

O1 - output terminal no. 1 for shutter motor

O2 - output terminal no. 2 for shutter motor

B - service button (used to add or remove a device from the system)

TIPS FOR ARRANGING THE ANTENNA:

Locate the antenna as far from metal elements as

possible (connecting wires, bracket rings, etc.) in

order to prevent interferences.

Metal surfaces in the direct vicinity of the antenna

(e.g. flush mounted metal boxes, metal door frames)

may impair signal reception!

Do not cut or shorten the antenna - its length is

perfectly matched to the band in which the system

operates

Note!

It should be noted that the push-button connected to

S1 terminal operates with the shutter motor output

(O1), while the push-button connected to S2

terminal, operates with the shutter motor output O2.

Therefore, it has to be defined which connected

push-button causes the Roller Shutter to move up /

down.

Note!

It should be noted that only the push-button

connected to S1 terminal and service push-button B

enables "self-learning" mode (Include/ Exclude).

DICTIONARY:

• INCLUSION (Adding) - a device sends "Node Info" frame, to

enable user to add it to Fibaro system (Home Center)

• EXCLUSION (Removing) - removing a device from the Fibaro

radio system

• ASSOCIATION - controlling other devices of system Fibaro system

• MultiChannelAssociation - controlling other multichannel devices

of Fibaro system

Danger of electrocution.

III Starting the operation of the

Roller Shutter Controller

1. Installing the Roller Shutter Controller

STEP 1

Connect the device in accordance with the circuit diagram presented

in Figure 1. Switch on 230V of the mains voltage.

[Adding/ Removing] of the Roller Shutter Controller [to/ from]

Z-wave network

STEP 2

The Roller Shutter Controller must be placed within the range of

Home Center controller, as the adding mode requires direct

communication with the controller.

STEP 3

Identify key no. 1. If the device is connected in accordance with the

diagram shown in Figure 1, this will the key that raises the roller

shutter.

STEP 4

Set the controller in add/remove mode (see the controller's manual)

S1 S2 O1

L N

Roller

STEP 5

Add the Roller Shutter Controller to the network by pushing three

Shutter

times (sat) key no. 1 or push-button B located inside the housing of

the device.

WARNING!

The Roller Shutter Controller cancels the "learning"

mode after key no. 1 is pressed once. Therefore,

pressing key no. 1 four times will not add the devices

to the network.

WARNING!

The Roller Shutter Controller is set by default to

operate with mono-stable switches (i.e. single-pole

switch or bell switch). While adding the Roller

Shutter Controller to the network with bi-stable

switches, ensure that all switch contacts are open

(off), because closing them results in activating the

push-button and this will prevent adding the device

to the network.

During the installation, it is recommended to use a

The Roller Shutter Controller enables user to associate three

mono-stable keys or push- button B.

groups.

Group I is triggered by single-clicking of any key (does not work

STEP 6

when using bi-stable keys )

The controller indicates that the device is correctly added to the

network, (see the manual of Home Center controller).

Group II is triggered by holding down any key

It should be noted that after proper adding the Roller Shutter

Group III for controllers such Home Center for state reporting

Controller to the Fibaro system, it should be calibrated. The

calibration process involves performing two complete cycles of

opening/ closing the shutter. Properly completed calibration may be

The Roller Shutter Controller enables user to control up to 16 normal

verified by setting required position of the shutter using the icon e.g.

devices, and 7 MultiChannel devices in group no. 1 and no. 2, group

30% of shutter opening - the actual opening should correspond to

no. 3 has only one field. The first field in each group is reserved for

this value/position.

the network controller. It is recommended to use up to 10 devices, as

the time required by the device to send a command to each

2. Resetting the Roller Shutter Controller

associated device may be quite long.

The Roller Shutter Controller provides two methods for resetting.

To add an association (using Fibaro controller), go to device options

Method I : Reset by removing the Roller Shutter Controller from the

by clicking the following icon:

existing Z-Wave network. The device may be removed using the

controller that has the ability to include/exclude devices from/to

Select the "device options" tab. Then specify to which group and

Z-Wave network (see the manual of controller).

what devices are to be associated. Sending relevant information to

devices added to associated groups may take even a few minutes

(see details in the controller's manual ).

Method II : Within 5 sec. after connecting mains voltage supply, the

Roller Shutter Controller allows the user to reset settings by pressing

once S1 key and then holding key S2.

3. Controlling the Roller Shutter Controller by

mono-stable or bi-stable switches.

Mono-stable switch (after releasing the push-button a spring

automatically pushes back and disconnects the button )

FGR221 Roller Shutter Controller supports the operation of

- Raising / lowering the roller shutter - shortly press the button

multi-channel devices. Multichannel devices are devices that include

assigned for the action.

two or more circuits inside one physical unit.

Bi-stable switch (operates as a two-position switch, it has no

spring that would push back the device after releasing manual

pressure)

V Configuration

- Raising / lowering the roller shutter - change the position of selected

push-button from the current position.

The Roller Shutter Controller allows user to configure the following

4. Controlling the Roller Shutter Controller using

parameters:

a command: ALL ON / ALL OFF

The Roller Shutter Controller responds to commands ALL ON / ALL

OFF that may be sent by the controller. ALL ON / ALL OFF

commands are usually implemented in Z-Wave remote control.

By default, the Roller Shutter Controller accepts both active

commands ALL ON and ALL OFF. Settings may be changed by

entering an appropriate value into configuration register no. 1

Parameter no. 1 - Activate / deactivate functions ALL ON / ALL

5. Controlling the Roller Shutter Controller using

OFF. default value 0

Fibaro system controller

Options for changing parameter 255, 0, 1, 2

After adding the Roller Shutter Controller to the network, it will be

Available configuration parameters:

255 - ALL ON active, ALL OFF active.

represented in Home Center by the following icon:

0 - ALL ON is not active ALL OFF is not active

1 - ALL ON is not active ALL OFF active

2 - ALL ON active ALL OFF is not active

Parameter no. 10 - Turning off the shutter positioning function

default value 0

Options for changing parameter 0, 1

0 - Turning on the shutter positioning function

1 - Turning off the shutter positioning function

Parameter no. 14 - Switch type connector, you may choose

between mono-stable and bi-stable switches default value 0

Options for changing parameter 0, 1, 2

Fig. 2 The icon of the roller shutter shown on the Fibaro controller

0 - mono-stable switch

1 - bi-stable switch

Raising / lowering the roller shutter is achieved by moving the slider

2 - single mono-stable switch

or by pressing the appropriate button, as shown in Figure 2.

Parameter no. 20 - Saving the position "Favourites"

IV Association

default value 16

Options for changing parameter 1-99

Association enables the Roller Shutter Controller to directly control

a device included in Z-Wave network e.g. Dimmer, Switch (ON-OFF)

or scene

Possibility to change the configuration of the following

parameters [30 - 33].

0 - DEACTIVATION - the device does not respond to alarm data

WARNING!

frames

Association ensures direct transfer of control

1 - CLOSED SHUTTER ALARM - the device closes the roller shutter

commands between devices, and is performed

after detecting an alarm

without participation of the main controller.

2 - OPEN SHUTTER ALARM - the device opens the roller shutter

after detecting an alarm

Parameter no. 30 - General Alarm, set for shutter no. 1

default value 1[byte] CLOSED SHUTTER ALARM

Parameter no. 31 - Alarm of flooding with water, set for relay the

shutter.

default value 0[byte] ALARM DEACTIVATION

Parameter no. 32 - Smoke, CO, CO2 Alarm. Set for the roller

shutter.

default value 1[byte] OPEN SHUTTER ALARM

Parameter no. 33 - Temperature Alarm, set for roller shutter

default value 1[byte] CLOSED SHUTTER ALARM

VI Additional Functionality

WARNING!

When the Roller Shutter Controller sends control

commands and a new command is issued, then the

Operating alarm data frames

current one command transmission is interrupted to

send new commands.

Fibaro system allows user to set response of devices to alarm

situations

(response

SENSOR_ALARM_REPORT)

responds to the following alarm types:

• General Purpose Alarm - GENERAL PURPOSE ALARM [0x00]

• Smoke Alarm - ALARM CO2 [0x02], ALARM CO [0x01], ALARM

SMOKE [0x03]

• Water Flooding Alarm - ALARM WATER [0x05]

• Temperature Alarm - ALARM HEAT [0x04]

Alarm data-frames are sent by devices that are system sensors (e.g.,

flood sensors, smoke detectors, motion detectors, etc.).

The device may respond in the following manner to received

data-frames (settings are configured in configuration parameters,

see section V Configuration ):

WARNING!

Entering incorrect parameters may cause incorrect

• 0 - DEACTIVATION - the device does not respond to alarm data

operation of the Roller Shutter Controller.

frames

• 1 - OPEN SHUTTER ALARM - the device opens the roller shutter

after detecting an alarm

• 2 - CLOSED SHUTTER ALARM - the device closes the roller

shutter after detecting an alarm

Position indicating

The Roller Shutter Controller has built-in mechanisms enabling it to

detect the current position of roller shutters, awnings and similar

devices. For proper operation of the mechanism, it is necessary to

use a motor with mechanical limit switches. Correct operation of the

position detecting mechanism, when using motor with overload

switches, depends on motor power and the suitability of specific

models - therefore it is recommended to use a motor with mechanical

limit switches. For each engine type the calibration procedure should

be performed.

VII Operating the Shutter Roller Controller

The Roller Shutter Controller may be operated using the

following control elements:

- any controller compatible with the system

- a mobile phone (e.g. iPhone and phones from other manufacturers

with appropriate software)

- devices of tablet type (such as iPad)

- PC, using a web browser

- using a push-button connected to the device

VIII Procedures for malfunctions

The device does not respond to a pre-programmed transmitter:

• Make sure that the maximum range is not exceeded and the signal

path is not obstructed by metal surfaces such as metal cabinets, etc.

• Make sure the device is not in the programming mode, or repeat

the programming process.

data-frames ALARM_REPORT

and

The

Roller

Shutter

Controller