Sharp CD DHS1050P Kullanım Kılavuzu - Sayfa 14

Stereo sistemi Sharp CD DHS1050P için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Sharp CD DHS1050P 17 sayfaları. Mini component system

Sayfayı Yazdır

Timer and sleep operation (Remote

control only) (continued)

To use timer and sleep operation together

Sleep and timer playback:

For example, you can fall asleep listening to the radio and

wake up to CD in the next morning.

Set the sleep time (see above, steps 1 - 5).

While the sleep timer is set, set the timer playback

(steps 2 - 10, page 12).

Sleep timer

Timer playback

setting

1 - 90 minutes

Sleep operation will

automatically stop

Enhancing your system

The connection cord is not included. Purchase a

commercially available cord as shown below.

Portable audio

player, etc.

To the

line

output

jack

PHONES

AUDIO IN

USB

Audio cable (not supplied)

Listening to the playback sounds of

portable audio player, etc.

Connect a portable audio player etc. to the front AUDIO

IN jack.

Press the ON/STAND-BY button to turn the power on.

Press the AUDIO IN/USB button repeatedly to select

AUDIO IN.

Play the connected equipment.

If volume level of the connected device is too high,

sound distortion may occur. Should this happen, lower

the volume of the connected device.

If volume level is too low, increase the volume of the

connected device.

Note:

To prevent noise interference, place the unit away from the

television.

Headphones

Before plugging in or unplugging the headphones,

reduce the volume.

Be sure your headphones have a 1/8" (3.5 mm) diameter

plug and impedance between 16 and 50 ohms. The

recommended impedance is 32 ohms.

Plugging in the headphones disconnects the speakers

automatically. Adjust the volume using the VOLUME

control.

Desired time

Timer playback

start time

MINI COMPONENT SYSTEM

CD-DHS1050P

TIMER

REMOTE

SENSOR

POWER

ON/ STAND-BY

OPEN / CLOSE

VOL.

iPod/iPhone

TUNER

(BAND)

TAPE

TUNING

PRESET

AUDIO IN

USB

Troubleshooting chart

Many potential problems can be resolved by the owner

without calling a service technician. If something is wrong

with this product, check the following before calling your

authorized SHARP dealer or service center.

General

Symptom

The clock is not set

to the correct time.

When a button is

End time

pressed, the unit

does not respond.

No sound is heard.

CD player

Symptom

Playback does not

start.

PHONES

Playback stops in

the middle or is not

performed properly.

Playback sounds

AUDIO IN

are skipped, or

stopped in the

middle of a track.

"ER-CD21"

appears on the

display.

Cassette deck

Symptom

Sound skipping.

Cannot hear treble.

Sound ﬂ uctuation.

Cannot remove the

tape.

E-13

Possible cause

Did a power failure occur?

Reset the clock. (Refer page

11)

Set the unit to the power

stand-by mode and then turn

it back on.

If the unit still malfunctions,

reset it. (Refer page 14)

Is the volume level set to "0"?

Are the headphones

connected?

Are the speaker wires

disconnected?

Possible cause

Is the disc loaded upside

down?

Does the disc satisfy the

standards?

Is the disc distorted or

scratched?

Is the unit located near

excessive vibrations?

Is the disc very dirty?

Has condensation formed

inside the unit?

Is the disc tray stopped with

force? Set the unit to the

power stand-by mode and

then turn it back on.

Possible cause

Is there any slack?

Is the tape stretched?

Are the capstans, pinch

rollers, or heads dirty?

If a power failure occurs

during playback, the heads

remain engaged with the

tape. Do not open the

compartment with great

force.