Sharp AR-5320 Servis Kılavuzu - Sayfa 8

Hepsi Bir Arada Yazıcı Sharp AR-5320 için çevrimiçi göz atın veya pdf Servis Kılavuzu indirin. Sharp AR-5320 20 sayfaları. Mono laser copier/printer
Ayrıca Sharp AR-5320 için: Yazılım Kurulum Kılavuzu (16 sayfalar), Broşür ve Teknik Özellikler (4 sayfalar)

Sayfayı Yazdır

Main

Sub

code

Image lead edge adjustment

Copy lead edge position adjustment (SPF/RSPF)

Paper off-center adjustment

Document off-center adjustment

Resist amount adjustment

SPF scanning position automatic adjustment

SPF scan position change-over setting

HSYNC output check

Shading check

SPF automatic correction

Self print

4. Contents of simulations

Main

Sub

Contents

code

Mirror scanning operation aging

Single paper feeder (SPF) aging

SPF sensor status display

Paper feed solenoid operation

check

Contents

When the [START] key is pressed, the mirror base performs A3 full scanning at the set magnification

ratio speed. During scanning, the set magnification ratio is displayed. After 3 seconds, the mirror

base performs full scanning again. During scanning, the set magnification ratio is displayed.

When the [START] key is pressed again, the ready lamp turns and remains off.

The DV replacement/OPC drum cartridge replacement lamp displays the status of the mirror

home position sensor. (The lamp lights up when the mirror is in the home position.)

During aging, the copy lamp lights up. When the [Interrupt] key is pressed, the operation is

interrupted if operating, and the machine goes into the sub code input standby mode.

When the [START] key is pressed, the set magnification ratio is acquired and document transport

operation of single surface is performed in the case of SPF or document transport operation of

duplex surfaces is performed. During operation, the LED on the display section corresponding to the

selected magnification ratio lights up, and the magnification ratio is displayed on the 7-seg display.

When the [Interrupt] key is pressed at that time, the machine goes to the sub code input standby

mode. When the [CA] key is pressed, the simulation is terminated.

(In order to receive the sensor change notification, the load must be decreased.)

The sensor status (ON/OFF) in the SPF can be checked with the following lamps.

When a sensor detects paper, it turns on. The open/close detection sensor turns on when the

machine is opened.

Display lamp

Toner supply lamp

Copier jam lamp

The DV replacement/OPC drum cartridge

replacement lamp

Paper empty lamp

SPF jam lamp

Manual paper feed lamp

Tray jam lamp

AE lamp

TEXT lamp

PHOTO lamp

When the [Interrupt] key is pressed, the machine goes to the sub code input standby mode.

When the [CA] key is pressed, the simulation is terminated.

When this simulation is executed, the sub code is displayed on the 7-seg LED and the lamp

corresponding to the solenoid lights up.

Select a solenoid with the tray select key (the lamp corresponding to the solenoid lights up) and

press the [START] key, and the machine repeats operation of ON for 500ms and OFF for 500ms.

This operation is repeated 20 times.

After that, the machine goes into the sub code entry standby mode.

When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input

standby mode. When [CA] key is pressed, the simulation is terminated.

Display lamp

Main cassette lamp

2nd cassette lamp

Manual paper feed lamp

2nd cassette jam lamp

Machine jam lamp & 2nd cassette jam lamp

Supported for the installed models only. Skipped for the models without installation.

AR-5316/5320 SIMULATIONS 7-2

Details of operation

Sensor

SPF document set sensor

SPF document transport sensor

SPF unit (OC cover) open/close sensor

SPF paper exit sensor

SPF paper feed cover open/close sensor

SPF paper length sensor 1

SPF paper length sensor 2

SPF paper feed width sensor (small)

SPF paper feed width sensor (middle)

SPF paper feed width sensor (large)

Solenoid

Main cassette paper feed solenoid

* 2nd cassette paper feed solenoid

Manual paper feed solenoid

* 2nd cassette paper transport solenoid

* 3rd cassette transport solenoid