Sharp AR-M550U Anahtar Kullanım Kılavuzu - Sayfa 12

Hepsi Bir Arada Yazıcı Sharp AR-M550U için çevrimiçi göz atın veya pdf Anahtar Kullanım Kılavuzu indirin. Sharp AR-M550U 20 sayfaları. Digital multifunctional system
Ayrıca Sharp AR-M550U için: Teknik Kılavuz (48 sayfalar)

Sharp AR-M550U Anahtar Kullanım Kılavuzu
GENERAL PROGRAMS

Operation settings

The "Operation settings" are related to basic operation
of the machine and consist of the following programs:
G Keys touch sound
G Auto clear setting
G Disabling of job priority operation
G Message time setting
G Disabling of bypass printing
G Display language setting
G Key operation setting
G Disabling of clock adjustment

Keys touch sound

This program is used to adjust (or turn off) the volume
of the beep that sounds when you touch a key. You can
also have three beeps sound at base values when
setting the ratio in copy mode or adjusting the exposure
in any mode.
KEY OPERATOR PROGRAMS
KEYS TOUCH SOUND
KEYS TOUCH SOUND
KEY TOUCH SOUND AT INITIAL POINT
Volume: Low
To change the volume, touch the desired volume key.
When "KEY TOUCH SOUND AT INITIAL POINT" is
selected, three beeps will sound at the base setting
values indicated below.
Screen in which setting is
effective
Ratio setting screen in main
screen of copy mode
Exposure adjustment screen in
main screen of copy mode
Exposure adjustment screen in
main screen of fax, Internet fax,
and network scanner modes
Exposure adjustment screen in
[SCAN TO HDD] in main
screen of document filing mode

Auto clear setting

If the machine is not used for a certain duration of time,
the auto clear function will clear any settings that have
been selected and return the screen to the main screen
of copy mode or the job status screen. This program is
used to set the duration of time after which auto clear
operates.The time can be set from 10 seconds to 240
seconds in increments of 10 seconds, or the auto clear
function can be disabled. (Note that auto clear can only
be disabled for copy mode.)
10
OK
Volume: High
Off
Base value
Ratio = 100%
Exposure level3
(middle level)

Disabling of job priority operation

This program is used to prohibit use of the [PRIORITY]
key in the job status screen.

Message time setting

This program is used to set the length of time that
messages appear in the display (this applies to
messages that appear for a certain length of time and
then automatically disappear.)
The time can be set to as long as 12 seconds in
increments of one second.

Disabling of bypass printing

When a job cannot be printed because there is no
suitable paper and there is a subsequent job that can
be printed, the subsequent job will be printed ahead of
the job that cannot be printed
"Operation manual (general information and copier
operation)"). This program can be used to disable
printing of subsequent jobs in this situation.
*1 Except when paper runs out in the middle of a job

Display language setting

This program is used to select the display language.

Key operation setting

These programs are used to set the length of time a
key in the touch panel must be touched before the key
input is registered, and to prevent repeated key input
when a key is touched continuously.
• Time until key input is registered
The time can be set from 0 seconds to 2 seconds in
increments of 0.5 seconds. Normally the time is set
to 0 seconds so that key input is immediately
registered when a key is touched. By lengthening the
time setting, key input can be prevented when a key
is touched accidentally. Keep in mind, however, that
when a longer setting is selected more care is
required when touching keys to ensure that key input
is registered.
• Prohibit key repeat
The touch panel contains keys such as the zoom
keys (for setting the ratio) that can
continuously to make a value change until it reaches
a desired value.
This feature whereby a value changes continuously
while a key is touched is called key repeat.
Key repeat is normally enabled. If you wish to prohibit
key repeat, select the "DISABLE AUTO KEY
REPEAT" checkbox.
(page 1-14 of the
*1
be touched