Crestron 4260596520153 Kılavuzdan - Sayfa 2

Kontrolör Crestron 4260596520153 için çevrimiçi göz atın veya pdf Kılavuzdan indirin. Crestron 4260596520153 2 sayfaları. Receiver and room controller 200

Sayfayı Yazdır

Installation of the power pack in the holder appears as shown

below.

Make Additional

Connections to the Device

Make additional connections as appropriate for the application.

Front Panel Connections

HDMI OUT:

HDMI

Digital

COM:

Video/Audio

To RS-232

Output

Device

USB HID:

DIG IN:

Software

From USB

To IR

Programmable

HID-Compliant

Controllable

Device

Digital Input

As of the date of manufacture, the product has been tested and found to comply with specifications for CE marking.

This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the

user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation.

GUIDE

Rear Panel Connections

AUDIO OUT R, L

(SPEAKER):

Ampli ed Stereo

Audio Output

NOTE:

Connection to the power pack is not required when

PoDM is used to power the device.

Set the IP Address

The configuration of the receiver within the DigitalMedia 8G+

system determines how the IP address of the receiver is set:

• If the receiver connects to a DigitalMedia™ switcher, the

receiver is configured by the switcher automatically.

• If the receiver connects to a DigitalMedia 8G+ transmitter,

the receiver uses its own configuration settings. By default,

DHCP (Dynamic Host Configuration Protocol) is enabled.

If desired, you can assign the default IP address to the

receiver by holding down the SETUP button while the unit

boots up. The default IP address overwrites the current

setting. The default IP address of the DM-RMC-200-C is

192.168.1.245. To manually set a different IP address, use

IR:

Crestron Toolbox™.

AUDIO OUT R, L

LAN:

10BASE-T/

(LINE):

Stereo Unbalanced

100BASE-TX

Line Level

Ethernet to Local

Audio Output

Network Device

24 V

2.5A MAX:

From Power

Pack (Included)

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Industry Canada (IC) Compliance Statement

CAN ICES-3(B)/NMB-3(B)

The specific patents that cover Crestron products are listed at patents.crestron.com.

Crestron, the Crestron logo, Crestron Toolbox, DigitalMedia, DigitalMedia 8G+, and DM are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/

or other countries. HDBaseT and the HDBaseT Alliance logo are either trademarks or registered trademarks of the HDBaseT Alliance in the United States and/or other countries. HDMI and the

HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may

be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron

is not responsible for errors in typography or photography.

This document was written by the Technical Publications department at Crestron.

1. The DM IN port is a PoDM (Power over DM) or PoH (Power over HDBaseT)

PD (Powered Device) port. To receive PoDM or PoH, the DM-RMC-200-C

requires a connection to a DigitalMedia switcher or other equipment that

has a PoDM or PoH PSE (Power Sourcing Equipment) port. Any wiring that

is connected to a PoDM or PoH PSE port is for intra-building use only and

should not be connected to a line that runs outside of the building in which

the PSE is located.

Learn More

Visit the website for additional information and the

latest firmware updates.

Crestron Electronics

15 Volvo Drive, Rockleigh, NJ 07647

888.CRESTRON | www.crestron.com

The product warranty can be found at www.crestron.com/warranty.

DOC. 7549A (2042263) 05.15

Specifications subject to change without notice.