Shimano PD-A530 Teknik Servis Talimatları

Müzik Pedalı Shimano PD-A530 için çevrimiçi göz atın veya pdf Teknik Servis Talimatları indirin. Shimano PD-A530 1 sayfaları. Spd pedals

Sayfayı Yazdır

General Safety Information

WARNING

– To avoid serious injuries:

SPD pedals are designed so that you release them only when

you intend to release. They are not designed to release

automatically at times such as when falling off the bicycle.

This is a safety measure to prevent you from losing balance

and falling off the bicycle as a result of your feet becoming

accidentally released from the pedals.

Use only SPD shoes with this product. Other types of shoes

may not release from the pedals, or may release

unexpectedly.

Use only Shimano cleats (SM-SH51/ SM-SH56) and tighten the

mounting bolts securely to the shoes.

Before attempting to ride with these pedals and shoes, make

sure you understand the operation of the engagement /

release mechanism for the pedals and cleats (shoes).

Before you attempt to ride with these pedals and shoes, apply

the brakes, then place one foot on the ground and practice

engaging and releasing each shoe from its pedal until you

can do so naturally and with minimal effort.

Ride on level ground first until you become adept at engaging

and releasing your shoes from the pedals.

Before riding, adjust the spring tension of the pedals to your

liking.

When riding at low speed or when there is a possibility that

you might need to stop riding, (for example, when doing a

U-turn, nearing an intersection, riding uphill or turning a blind

curve), release your shoes from the pedal beforehand so that

you can quickly put your feet onto the ground at any time.

Use a lighter spring tension for attaching the pedal cleats

when riding in adverse conditions.

Keep cleats and bindings clear of dirt and debris to ensure

engagement and release.

Remember to check the cleats periodically for wear. When the

cleats are worn, replace them. Always check the spring

tension after replacing the pedal cleats and before ridingIf.

If you do not maintain both your shoes and cleats in good

condition, release and engagement to the pedals could

become unpredictable or difficult, which could result in

severe injury.

Be sure to attach reflectors to the bicycle when riding at

night. Do not continue riding the bicycle if the reflectors are

dirty or damaged, otherwise it becomes more difficult for

oncoming vehicles to see you.

Obtain and read the service instructions carefully prior to

installing the parts. Loose, worn, or damaged parts may

cause serious injury to the rider.

We strongly recommend only using genuine Shimano

replacement parts.

If you have any questions concerning your pedals, contact a

professional dealer.

Read these Technical Service Instructions carefully, and keep

them in a safe place for later reference.

BE SURE TO READ AND FOLLOW THE ABOVE

WARNINGS CAREFULLY.

If the warnings are not followed, your shoes may not

come out of the pedals when you intend or they may

come out unexpectedly or accidentally, and severe injury

may result.

NOTE:

Before riding the bicycle, check that there is no play or

looseness in the connection. Also, be sure to retighten the

crank arms and pedals at periodic intervals.

In addition, if pedaling performance does not feel normal,

check this once more.

Parts are not guaranteed against natural wear or deterioration

resulting from normal use.

For maximum performance we highly recommend Shimano

lubricants and maintenance products.

These pedals have an SPD-type face on one side and a standard

face on the other side.

Cleat types and using the pedals

WARNING

Do not use the pedals and cleats in any way other

than as described in these Service Instructions. The

cleats are designed to engage and release from the

pedals when the cleats and pedals are facing

forward.

See below for instructions on how to install the

cleats.

FAILURE TO FOLLOW THESE INSTRUCTIONS MAY

RESULT IN SERIOUS PERSONAL INJURY.

Single release mode cleats (SM-SH51) and multiple

release mode cleats (SM-SH56) are available for use

with these pedals.

Each type of cleat has its own distinctive features,

so be sure to read the Service Instructions carefully

and select whichever type of cleat best suits your

riding style and the terrain and riding conditions

which you will encounter.

Other types of cleats such as single release mode

cleats (SM-SH52) and multiple release mode cleats

(SM-SH55) cannot be used, as they do not provide

stable enough step-out performance or sufficient

holding force.

Engaging the cleats with the pedals

Press the cleats into the pedals with a forward and downward

motion.

SI-45R0A-002

PD-A530

SPD Pedals

Technical Service Instructions

Attaching the cleats

Remove the sockliner and position a cleat nut over the oval

holes.

Note:

This step may not be necessary depending on the type of

shoes.

Cleat nut

Sockliner

Releasing the cleats from the pedals

The method of release varies according to the type of cleats you are using.

(Check the model number and color of your cleats to determine the proper method of release.)

Single release mode cleats:

SM-SH51 (black)

These cleats only release when the heel is twisted outward.

The cleats can be released by twisting in any direction.

They will not release if the heel is twisted in any other direction.

You are able to apply upward force to the pedal, since they will

Because the cleats can also be released by lifting your heel, they

not release unless the foot is twisted outward.

may become accidentally released when applying upward force

on the pedals.

These cleats should not be used for riding style which may involve

pulling up on the pedals or for activities, such as jumping, in which

pulling forces are applied to the pedals causing possible release

from the pedals.

The cleats will not necessarily release if you lose your balance.

Although the cleats can be released by twisting your heels in any

Accordingly, for places and conditions where it looks as though

direction or by lifting, they will not necessarily release if you lose

you may lose balance, make sure that you have sufficient time to

your balance.

release the cleats beforehand.

Accordingly, for places and conditions where it looks as though

you may lose balance, make sure that you have sufficient time to

release the cleats beforehand.

When you are pedaling vigorously, your heel may inadvertently

If the cleats release by accident, you may fall off the bicycle and

twist outward and this may cause the cleat to release accidentally.

serious injury may result.

If the cleat releases by accident, you may fall off the bicycle and

If the features of multiple release mode cleats are not sufficiently

serious injury may result.

understood and if they are not used correctly, then they may

You can help to prevent this by adjusting the amount of force

release accidentally with a greater frequency than for single

required to release the cleats, and you should practice until you

release mode cleats.

are accustomed to the amount of force and the angle required to

You can help to prevent this by adjusting the amount of force

release the cleats.

required to release the cleats in any direction, and you should

practice until you are accustomed to the amount of force and the

angle required to release.

Single release mode

Release the cleats from the pedals by twisting

your heels outward.

Note:

It is necessary to practice

releasing until you become

accustomed to the technique.

From the bottom of the shoe, position a cleat and then a cleat

adapter over the cleat holes. The cleats are compatible with both

left and right pedals. Provisionally tighten the cleat mounting

bolts.

Provisional tightening torque

for cleat mounting bolts:

2.5 N·m {22 in. lbs.}

4 mm Allen key

Cleat mounting bolts

Cleat

Cleat adapter

Front

Position the triangular

portion of the cleat toward

the front of the shoe.

Adjusting the cleat position

The cleat has an adjustment range of 20 mm front

to back and 5 mm right to left.

After provisionally tightening the cleat, practice

engaging and releasing, one shoe at a time.

Readjust to determine the best cleat position.

After you have determined the best cleat position,

firmly tighten the cleat mounting bolts with a 4 mm

Allen key.

Tightening torque:

5 – 6 N·m {43 – 52 in. lbs.}

Multiple release mode cleats:

SM-SH56 (silver, gold /Optional accessory)

Multiple release mode

Release the cleats from the pedals by twisting

your heels in any direction.

Note:

In multiple release mode, it is

necessary to practice

releasing until you become

accustomed to the technique.

Releasing by lifting your heel

requires particular practice.

Waterproof seal

Remove the sockliner and attach

Waterproof seal

the waterproof seal.

Sockliner

Note:

The waterproof seal is

supplied with Shimano

shoes which require this

step to be carried out.

Mounting the pedals on the crank arms

Use a 15 mm spanner to mount the pedals on the crank arms. The

right pedal has a right-hand thread; the left pedal has a left-hand

thread.

Pay attention to

the mark

R: right pedal

L : left pedal

15 mm spanner

Tightening torque:

35 – 55 N·m {304 – 477 in. lbs.}

Note:

A 6 mm Allen key cannot provide a sufficient tightening torque.

Always be sure to use a 15 mm spanner.

Adjusting the spring tension of the

binding

The spring force is adjusted by means of adjustment bolts. The

adjustment bolts are located behind each of the bindings, and there

is one adjustment bolt on each pedal. Equalize the spring tensions

by referring to the position of the adjustment plates and by counting

the number of turns of the adjustment bolts. The spring tension can

be adjusted in four steps for each turn of the adjustment bolt.

Adjustment bolt

Adjustment plate

Adjustment

bolt

Decrease

Increase

3 mm Allen key

When the adjustment bolt is turned clockwise, the spring tension

increases, and when it is turned counterclockwise, the spring

tension decreases.

Strongest position

Weakest position

Adjustment

bolt

Adjustment plate

If the adjustment plate is at the strongest or the weakest

position, do not turn the adjustment bolt any further.

Note:

In order to prevent accidental release from occurring, make

sure all the spring tensions are properly adjusted.

The spring tensions should be adjusted equally for both right

and left pedals. If they are not adjusted equally, it can cause

the rider difficulty to engage or release from the pedals.

Mounting the reflectors

(optional)

An optional reflector set (SM-PD61) is available. Please contact a

professional dealer for details.

Cleat replacement

Cleats wear out over time and should be replaced periodically.

Cleats should be replaced when it becomes difficult to release, or it

starts to release with much less effort than the when it was in new

condition.

Maintenance of the axle units

If you experience any trouble with the rotating parts of the pedal, the

pedal may require adjustment. Obtain advice from a professional

dealer.

Please note: Specifications are subject to change for improvement without notice.

(English)

One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003

Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222

3-77 Oimatsu-cho, Sakai-ku, Sakai, Osaka 590-8577, Japan

Apr. 2009 by Shimano Inc. PIT. IZM. Printed in Malaysia