Crestron 3 Series Kılavuzdan - Sayfa 2

Kontrol Sistemleri Crestron 3 Series için çevrimiçi göz atın veya pdf Kılavuzdan indirin. Crestron 3 Series 2 sayfaları. Automated processors
Ayrıca Crestron 3 Series için: Hızlı Başlangıç Kılavuzu (2 sayfalar), Hızlı Başlangıç (2 sayfalar), Kılavuzdan (2 sayfalar), Hızlı Başlangıç Kılavuzu (6 sayfalar), Hızlı Kılavuz (2 sayfalar), Hızlı Başlangıç Kılavuzu (2 sayfalar), Hızlı Başlangıç Kılavuzu (8 sayfalar), Kullanım Kılavuzu (20 sayfalar)

Sayfayı Yazdır

Configure the Control System

The RMC3 can be configured using the Crestron Toolbox™

software and the built-in, web-based setup tool.

1. Use Crestron Toolbox to set the time zone. For details,

refer to the embedded Crestron Toolbox help file.

2. Use the Internet Explorer

web browser to navigate to

http://xxx.xx.xx.xxx/setup, where xxx.xx.xx.xxx is the

IP address of the control system. The control system's

welcome screen displays.

NOTE:

The web-based setup tool is accesible only from

Internet Explorer.

NOTE:

If a security warning is displayed, click Install to

continue. Click Setup to display the RMC3 Setup menu.

As of the date of manufacture, the product has been tested and found to comply with specifications for CE marking.

This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.

Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the

user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation.

GUIDE

3. The RMC3 Setup menu displays the IP address, the

hostname, and the MAC address of the device. This menu

also provides access to various setup and programming

screens.

4. From the RMC3 menu, click the following options to

configure the control system:

• Ethernet Setup configures the RMC3's Ethernet

settings and displays DHCP, hostname, IP address,

subnet mask, default router, domain, and MAC

address settings. In the Ethernet Setup menu, there

are additional options:

• Click Advanced Settings to specify DNS

servers, web server settings, and SSL settings.

• Click MyCrestron Dynamic DNS to configure

the myCrestron.com Dynamic DNS service.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a limited non-exclusive, non-transferable Software Development Tools

License Agreement. Crestron product operating system software is licensed to Crestron dealers, CSPs, and end-users under a separate End-User License Agreement. Both of these Agreements

can be found on the Crestron website at www.crestron.com/legal/software_license_agreement.

The specific patents that cover Crestron products are listed at http://www.crestron.com/legal/patents.

Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.

Crestron, the Crestron logo, 3-Series, Cresnet, and Crestron Toolbox are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries.

Internet Explorer is either a trademark or a registered trademark of Microsoft Corporation in the United States and/or other countries. Other trademarks, registered trademarks, and trade names

may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others.

Crestron is not responsible for errors in typography or photography.

This document was written by the Technical Publications department at Crestron.

• Click Ethernet Diagnostics to test Ethernet

communications.

• Click Reboot to reboot the RMC3.

• Application Setup selects programs to be loaded on

startup and controls what programs are running.

• Input/Output Control configures the COM ports,

operates the relays, and monitors the digital inputs.

• Diagnostics displays information about the

connected devices, hardware configuration, and error

logs.

• About displays firmware information.

Click the back (

) button to return to the previous screen.

Learn More

Visit the website for additional information and the

latest firmware updates. To learn more about this

product, use a QR reader application on your

mobile device to scan the QR image.

Crestron Electronics

15 Volvo Drive, Rockleigh, NJ 07647

888.CRESTRON | www.crestron.com

The product warranty can be found at www.crestron.com/warranty.

DOC. 7962A (2047947) 11.16

Specifications subject to change without notice.