Epson 1815p - PowerLite XGA LCD Projector Kullanıcı Kılavuzu - Sayfa 15

Projektör Epson 1815p - PowerLite XGA LCD Projector için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Epson 1815p - PowerLite XGA LCD Projector 27 sayfaları. Release of check tool for network projectors v1.00 for windows
Ayrıca Epson 1815p - PowerLite XGA LCD Projector için: Kullanıcı Kılavuzu (42 sayfalar), Kullanım Kılavuzu (36 sayfalar), Kullanım Kılavuzu (47 sayfalar), Hızlı Kurulum (2 sayfalar), Kullanıcı Kılavuzu (1 sayfalar), İşlev Kılavuzu (5 sayfalar), Yazılım Kılavuzu (2 sayfalar), Uygunluk Beyanı (4 sayfalar), Parça Listesi (1 sayfalar), Ürün Destek Bülteni (45 sayfalar), Ürün Destek Bülteni (25 sayfalar), Ürün Destek Bülteni (22 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (41 sayfalar), Ürün Destek Bülteni (34 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (15 sayfalar), Ürün Destek Bülteni (22 sayfalar)

Sayfayı Yazdır
Epson 1815p - PowerLite XGA LCD Projector Kullanıcı Kılavuzu
8. Right-click the
Wireless Network Connection
and select
. You see this screen:
Properties
9. Select
Internet Protocol
You see this screen:
10.If your access point uses DHCP, select
address automatically
and
following IP address
, then enter the required information:
addresses
❏
: Type in the IP address you want to assign to
IP address
the computer. It must be formatted like other addresses
on the network. The last octet should be unique.
❏
: For example: 255.255.255.000, but this
Subnet mask
depends on how your network is set up.
❏
: Enter the IP address that was assigned
Default gateway
to the access point when it was set up.
icon again
and click the
button.
Properties
Obtain an IP
. Otherwise select
Use the
Use the following DNS server
❏
Preferred DNS server/Alternate DNS server:
the IP address of the DNS server(s) for your network.
11.When you're done, click
12.Click the
Wireless Networks
you may need to enable your wireless card or adapter by
clicking
Configure
any instructions on the screen to enable the device.)
You see a screen like this:
13.Verify that you've enabled your computer's connection to
the access point. It should be listed with the small
next to it, indicating a connection. If it's not listed, click
and type the name of your access point.
Configure
14.When you're done making settings, click
dialog box.
Now you're ready to connect to the projector. See "Projecting
Over a Network" on page 17.
Note: On some Windows systems, you can right-click
or
Places
Network Neighborhood
. Settings may vary, depending on your wireless network
Properties
adapter. See the documentation for your adapter for more
information.
3/08
PowerLite 1810p/1815p
.
OK
tab. (If you don't see this tab,
to access the device settings; then follow
to close the
OK
on the desktop and select
PowerLite 1810p/1815p
Enter
icon
My Network
15
-