Cisco 3600 Series Kullanıcı Kılavuzu - Sayfa 13

IP Telefon Cisco 3600 Series için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Cisco 3600 Series 25 sayfaları. Memory upgrade
Ayrıca Cisco 3600 Series için: Ürüne Genel Bakış (10 sayfalar), Yükseltme Talimatları (30 sayfalar), Kullanıcı El Kitabı (17 sayfalar), Uygulama Notu (41 sayfalar), Yapılandırma Kılavuzu (36 sayfalar), Ekler (15 sayfalar), Kullanıcı Kılavuzu (7 sayfalar), Manuel (5 sayfalar), Yapılandırma Notu (23 sayfalar), Yapılandırma Notu (18 sayfalar), Yapılandırma Notu (25 sayfalar)

Sayfayı Yazdır
Cisco 3600 Series Kullanıcı Kılavuzu
V.110 Support for Cisco 3600 Series Digital Modems

show modem log

To display the modem history event status performed on a manageable modem or group of modems, use
the show modem log EXEC command.
Syntax Description
slot/port
group number
Defaults
There are no default behaviors or values for this command.
Command Modes
EXEC
Command History
Release
11.2
12.1(5)T
Examples
The following example shows a portion of the output display when using the show modem log
command. Since no specific modem or range of modems is designated, the data from all modems is
shown. The V.110 information is highlighted in this example.
Router# show modem log
Modem 0/0 Mica: Event Log contains 100 Events:
1d21h MICA-Cfg issued S-Reg configuration change:
1d21h CSM: Incoming call from 9195555301 to Unknown
1d21h CSM: event-ISDN_CALL New State-IC_MODEM_RESERVED
...
1d21h CSM: event-MODEM_CONNECTED New State-CONNECTED_STATE
1d21h MICA-Qry Static Link Information:
1d21h MICA-Cmd Set Framing Mode to PPP.
...
1d21h MICA-Qry Final Link Information:
show modem log [slot/port | group number]
(Optional) Specifies the location of a slot and modem port. If this number
is not specified, statistics for all connected modems are displayed.
Remember to include the forward slash (/) when entering this variable.
(Optional) Specifies the location of a specific group of modems. If this
number is not specified, statistics for all modems in the access server are
displayed. The group number range is from 1 to 200.
Modification
This command was introduced.
This command was modified to show display output for Cisco 3600 series
digital modems that support V.110.
configuration index = 59, value = 0x3
CSM: status-1 dchan-3/2 bchan-0
Connect Protocol - V.110, Compression - None, Connected Standard - V110
Tx/Rx Symbol Rate - 0/0, Tx/Rx Carrier Freq - 0/0
Tx/Rx Trellis Coding - /, Frequency offset - 0Hz
Round trip delay - 0ms, Tx/Rx bit rate - 2400/2400
RBS pattern - 0x0, digital pad - , compensation - 0
Call Time - 00:00:34, Disconnect Reason (0x8001) - SOFTWARE_RESET command
0 retrains and/or speed shifts, 0 ec retransmissions
9454 chars tx, 6577 chars rx, 0 chars rx bad
show modem log
Cisco IOS Release 12.1(5)T
13