Epson 755c - PowerLite XGA LCD Projector Parça Kılavuzu - Sayfa 18

Projektör Epson 755c - PowerLite XGA LCD Projector için çevrimiçi göz atın veya pdf Parça Kılavuzu indirin. Epson 755c - PowerLite XGA LCD Projector 26 sayfaları. Release of check tool for network projectors v1.00 for windows
Ayrıca Epson 755c - PowerLite XGA LCD Projector için: Kullanıcı Kılavuzu (42 sayfalar), Kullanım Kılavuzu (36 sayfalar), Şartname Sayfası (2 sayfalar), Kullanım Kılavuzu (47 sayfalar), Ürün Destek Bülteni (30 sayfalar), Kullanıcı Tarafından Değiştirilebilir Öğeler (1 sayfalar), Hızlı Kurulum (2 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kullanıcı Kılavuzu (1 sayfalar), İşlev Kılavuzu (5 sayfalar), Ürün Destek Bülteni (25 sayfalar), Ürün Destek Bülteni (38 sayfalar), Ürün Destek Bülteni (12 sayfalar), Ürün Destek Bülteni (42 sayfalar), Ürün Destek Bülteni (22 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (41 sayfalar), Ürün Destek Bülteni (34 sayfalar), Ürün Destek Bülteni (38 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (15 sayfalar), Ürün Destek Bülteni (22 sayfalar)

Sayfayı Yazdır
Epson 755c - PowerLite XGA LCD Projector Parça Kılavuzu
Epson PowerLite 755c/765c Projector
3. Click
Use IP connect mode
screen:
4. Click
. You see this screen:
IP connection
5. Enter the projector's IP address and click
The IP address is shown in the Projector list and a
searching icon appears.
This icon appears if the search fails
to find the projector
18
Epson PowerLite 755c/765c Projector
-
, then click
. You see this
OK
Click here
Enter the IP
address and
click Search
.
Search
If the search fails to find a projector with the specified IP
address, the searching icon turns into a question mark.
If this happens, run EasyMP to check the projector's IP
address, then repeat this step.
Note:
If you still don't see the projector, make sure the Internet
connection firewall is disabled.
6. Click the projector you want to connect to, then click the
button. If more than one projector is listed, you
Connect
can select additional projectors and connect to them at the
same time.
7. If you are prompted for a keyword, enter the four-digit
number displayed on the EasyMP Network screen and
click
.
OK
The computer's image is transmitted to the projector and
appears on the screen.
Removing the Wireless 802.11G/B Card
Follow these steps to remove the card from your projector:
1. If you're running NS Connection, click
control bar.
2. Check the card access light to make sure it isn't flashing.
Caution:
Never remove the card while the card access light is green or
flashing. You may damage the card or lose data.
3. Press the eject button. The button pops out.
Eject button
Access light
4. Press the eject button again. The wireless card partially
ejects.
5. Pull the card straight out. Then press the eject button back
in to prevent it from being damaged.
8/05
on the
Disconnect
Click here