Epson 835p - PowerLite XGA LCD Projector Kullanım Kılavuzu - Sayfa 38

Projektör Epson 835p - PowerLite XGA LCD Projector için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Epson 835p - PowerLite XGA LCD Projector 47 sayfaları. Release of check tool for network projectors v1.00 for windows
Ayrıca Epson 835p - PowerLite XGA LCD Projector için: Kullanıcı Kılavuzu (42 sayfalar), Kullanım Kılavuzu (36 sayfalar), Hızlı Kurulum (4 sayfalar), Ürün Destek Bülteni (30 sayfalar), Tamamlayıcı Kılavuz (1 sayfalar), Broşür ve Teknik Özellikler (4 sayfalar), Ürün Bilgileri (21 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kullanıcı Kılavuzu (1 sayfalar), Teknik Özet (7 sayfalar), İşlev Kılavuzu (5 sayfalar), Ürün Destek Bülteni (25 sayfalar), Ürün Destek Bülteni (38 sayfalar), Ürün Destek Bülteni (12 sayfalar), Ürün Destek Bülteni (42 sayfalar), Ürün Destek Bülteni (22 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (41 sayfalar), Ürün Destek Bülteni (34 sayfalar), Ürün Destek Bülteni (38 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (15 sayfalar), Ürün Destek Bülteni (22 sayfalar), Şartname Sayfası (4 sayfalar)

Epson 835p - PowerLite XGA LCD Projector Kullanım Kılavuzu

Mail notification function settings

Mail notification function settings
The mail notification function can be used to send corresponding
notification messages to a preset e-mail address when a projector that is
connected to the network assumes a certain status, or if it experiences a
problem or warning. By using this function, the operator can be notified
of a projector's status or problems even when the operator is in a
different location from the projectors.
• Up to three addressees (destinations) can be registered and messages can be
q
sent to all of them at once.
• If a critical problem develops with a projector which causes it to suddenly
stop working, it may not be possible for the projector to send a message
notifying an operator of the problem.
• If Standby Mode is set to Communication On (or Network On) or Network
Monitoring is set to On in the projector configuration menus, you can
monitor the projector even when it is in standby mode (when its power is
turned off). s Projector's User's Guide
• On some projectors, the mail notification function can be set in the
configuration menu. When notification messages are set to be sent in the
projector's configuration menu, both the settings in the configuration menu
and settings made on EasyMP Monitor are functional.
• Detectable status with the mail notification function differs depending on
the projector you are using.
Procedure
A
Select "Mail notification function" from the Tool menu.
B
The Set mail notification function window will be displayed.
Make the necessary settings while referring to the table below.
Mail notification
Set to On to use the mail notification function.
function
SMTP server IP
Enter the IP address of the SMTP server. Up to
address
a maximum of 255 bytes can be entered.
When you change a port number of the SMTP
server, specify this port number. The default
value is "25".
You can enter a valid number from 1 to 65535.
Sender mail
Enter the sender's e-mail address. Up to a
address
maximum of 255 bytes can be entered.
Recipient mail
Specify the destination addresses for the
address 1
notification e-mail. Up to three destinations
can be set. Up to a maximum of 255 bytes can
Recipient mail
be entered.
address 2
Recipient mail
address 3
38