Epson 835p - PowerLite XGA LCD Projector Ürün Bilgileri - Sayfa 18

Projektör Epson 835p - PowerLite XGA LCD Projector için çevrimiçi göz atın veya pdf Ürün Bilgileri indirin. Epson 835p - PowerLite XGA LCD Projector 21 sayfaları. Release of check tool for network projectors v1.00 for windows
Ayrıca Epson 835p - PowerLite XGA LCD Projector için: Kullanıcı Kılavuzu (42 sayfalar), Kullanım Kılavuzu (36 sayfalar), Hızlı Kurulum (4 sayfalar), Kullanım Kılavuzu (47 sayfalar), Ürün Destek Bülteni (30 sayfalar), Tamamlayıcı Kılavuz (1 sayfalar), Broşür ve Teknik Özellikler (4 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kullanıcı Kılavuzu (1 sayfalar), Teknik Özet (7 sayfalar), İşlev Kılavuzu (5 sayfalar), Ürün Destek Bülteni (25 sayfalar), Ürün Destek Bülteni (38 sayfalar), Ürün Destek Bülteni (12 sayfalar), Ürün Destek Bülteni (42 sayfalar), Ürün Destek Bülteni (22 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (41 sayfalar), Ürün Destek Bülteni (34 sayfalar), Ürün Destek Bülteni (38 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (15 sayfalar), Ürün Destek Bülteni (22 sayfalar), Şartname Sayfası (4 sayfalar)

Sayfayı Yazdır
Epson 835p - PowerLite XGA LCD Projector Ürün Bilgileri
Epson PowerLite 835p
If the dirt is difficult to remove or a filter is broken, replace
the filters as described in the next section. Contact your
dealer, by calling Epson at (800) 873-7766, or by visiting the
SM
Epson Store
at www.epsonstore.com (U.S. sales only). In
Canada, please call (800) 463-7766 for dealer referral.

Replacing the Lamp and Air Filters

The life span of the projection lamp is about 2000 hours if
in the Setting menu is set to
Brightness Control
and 3000 hours if
Brightness Control
Note: When you get a replacement lamp for your projector, you
should replace the filters.
It is time to replace the lamp when:
The projected image gets darker or starts to deteriorate.
The message
Replace the lamp
the lamp comes on and the
orange. To maintain projector brightness and image
quality, replace the lamp as soon as possible.
The
lamp warning light flashes red (the lamp is burnt
out).
Contact your dealer or call Epson at (800) 873-7766 in the
United States for a replacement lamp. Request part number
V13H010L31. In Canada, please call (800) 463-7766 for
dealer referral.
Follow these steps to replace the lamp and air filters:
1. Turn off the projector.
2. When the
light stops flashing, unplug the power
Power
cord.
WARNING: Let the lamp cool fully before replacing it. It is
extremely hot immediately after use.
In the unlikely event that the lamp has broken, small glass
fragments may be present and should be removed carefully to
avoid injury.
18
Epson PowerLite 835p
-
(default),
High
is set to
.
Low
appears on the screen when
lamp warning light flashes
3. Let the projector cool for at least an hour (if it has been on).
The lamp is extremely hot immediately after use.
4. Turn the projector over and remove the air filters at the side
and bottom of the projector.
5. Insert the two new air filters. They should click into place.
6. Turn the projector back over.
7. Loosen the screw holding the lamp cover in place (you
don't need to remove it). Then remove the lamp cover.
8. Loosen the two screws holding the lamp in place (you don't
need to remove them).
9. Grasp the handles as shown and pull the lamp straight out.
10/04
Loosen, but
don't remove
these screws