Siemens ATS-150 Kurulum ve Kullanım Talimatları - Sayfa 2
Bulaşık Makinesi Siemens ATS-150 için çevrimiçi göz atın veya pdf Kurulum ve Kullanım Talimatları indirin. Siemens ATS-150 2 sayfaları.
Sayfayı YazdırMaintenance and care
Strainers ...
Rotate filter
cylinder, remove
Check, if
filter system ...
required, clean
Spray arms ...
Pull lower arm
upwards ...
Remove
blockages/deposits
Rectifying minor faults yourself ...
Fault
Possible causes
Residual water
Waste water pump blocked
in the appliance
The programme has not yet ended
Appliance is not running /
Supply fitting not open
stops
Supply hose kinked
Check water supply
Supply fitting jammed or calcified
Display lights up
Plastic / utensils
Too little detergent
discoloured
Discoloration caused by food colourings
(tomato sauce)
Rust on the cutlery
Cutlery not rust-resistant
Hard knife blades are more susceptible
Extraneous rust
Stopping the programme ...
Press and hold the two
reset buttons simultaneously for
approximately 3 seconds while
the programme is running
(RESET)
For perfect rinsing results ...
rinse under
flowing water ...
Unscrew upper
arm ...
... as it is worth doing it yourself!
Remedial action
Fault
Clean waste-water pump (see above).
Utensils are not clean
Close appliance and switch on.
Sand or gritty residue
or terminate programme (see
on the utensils
Terminating the programme).
Open supply fitting.
Install supply hose without kinks.
1. Unscrew water connection.
2. Clean filter in the water connection.
3. Flow rate must be min. 9 l/min. when
water supply is open.
Stains and streaks
If the flow rate is less, replace the
supply fitting.
Milky film on the utensils
(removable)
Follow manufacturer's instructions
(detergent).
Milky film, glasses
cloudy / dull
Discoloration is harmless; subsequent
(not removable)
rinse cycles will cause it to fade.
Use dishwasher-proof cutlery.
Never wash rusting parts
in the appliance.
"0" appears
Switch off the appliance.
The programme will stop
after 1 minute
Insert ...
Screw in filter
system NOTE
MARK!
Clean spray nozzles
Insert lower arm ...
under flowing water
(perhaps with
toothpick) ...
Screw in upper arm
Possible causes
Utensils are situated close together
or one above the other
Too little detergent
Unsuitable programme selected
Spray arm nozzles blocked
Filters dirty, not seated firmly
Spray arms blocked
Rinse-aid dosage too high / too low
Water softening system incorrectly set;
No salt
Glasses not dishwasher-proof.
Loading the dishwasher correctly ...
Arrange dishwasher-proof utensils (having removed any ash, wax, grease, ink, sticky labels; remove,
large remnants of jam, dairy products and food) according to the operating instructions and check that
the spray arms can rotate freely.
Cleaning the waste-water pump *
* With some models
– Ladle out water and remove filters
– Unscrew cover (Torx T20)
– Check area of fan impeller for foreign objects
– Screw in cover and insert filters
Remedial
action
Separate the utensils, prevent contact
points.
Follow manufacturer's instructions
(detergent).
Select a more intensive programme.
Clean the spray arms (see above).
Clean the filters (see above).
Arrange the utensils so that the spray
arms can rotate freely.
Streaks: reduce dosage.
Water or limescale stains: increase
dosage.
Correctly set water softening system.
Refill with salt.
Use dishwasher-proof glasses.
Use a detergent suitable for glasses.
More information can be found in the operating instructions