Ricoh Aficio CL5000 Hızlı Kurulum Kılavuzu - Sayfa 3
Yazıcı Ricoh Aficio CL5000 için çevrimiçi göz atın veya pdf Hızlı Kurulum Kılavuzu indirin. Ricoh Aficio CL5000 4 sayfaları. Ricoh cl5000 laser printer quick installation guide
Ayrıca Ricoh Aficio CL5000 için: Kullanım Talimatları (2 sayfalar), Hızlı Kurulum Kılavuzu (4 sayfalar), Tamamlayıcı Kılavuz (3 sayfalar), Manuel (12 sayfalar)
Sayfayı Yazdır
Sheet 2/2 (From sheet 1/2)
CONNECTING THE POWER
LOADING PAPER
CORD
Caution
• The paper tray does not have a stopper. When
Warning
pulling it out, be careful not to pull it strongly. If
• It is dangerous to handle the plug with wet hands.
you do, the tray might fall and cause an injury.
Doing this may result in receiving an electric
shock.
The following procedure describes how to load A4/letter
Kpaper.
Caution
For more information about the paper sizes that can be set
• When you pull the plug out of the socket, grip
in the paper tray, see "Paper Sizes" in Maintenance Guide
the plug, not the cord, to avoid damaging the
2 on the CD-ROM labeled "Operating Instructions".
cord and causing a fire or an electric shock.
For information about loading paper size other than A4/
letter, see "Loading Paper" in Maintenance Guide 2 on the
CD-ROM labeled "Operating Instructions".
For information about loading paper on the Bypass Tray,
Be sure to connect the power plug to the socket or
the wall outlet firmly.
see "Loading Paper" in Maintenance Guide 2 on the CD-
The printer power must be off when plugging in
ROM labeled "Operating Instructions".
and out the power cord.
Pull out the paper tray slowly until it stops.
Confirm that the printer's power switch is off. If it
is on, turn it off.
ZESX329E
Lower the base panel by pushing "Push".
Attach the power cord to the socket on the back
of the printer.
ZESX330E
Load paper into the tray with the print side up.
Plug the other end securely into the wall outlet.
ZESX331E
Important
Make sure that the top of the stack is not higher
than the limit mark inside the tray.
The front and side guides should be set exactly to
the paper size to avoid paper misfeeds.
Do not load different kinds of paper in the tray.
Slide the paper tray completely into the printer.
Important
Be sure to insert the paper tray completely.
Otherwise, misfeeds might occur, or the front cover
might touch the paper tray.
SELECTING THE PANEL
DISPLAY LANGUAGE
Follow the procedure to select a language.
Note
You can select one of the following languages:
English, German, French, Italian, Dutch, Swedish,
Norwegian, Danish, Spanish, Finnish, Portuguese,
Czech, Polish or Hungarian.
The default setting is English.
If you want to use the English panel display, it is
not necessary for you to take the following
procedures.
Important
Turn on the printer.
When the power is turned on, the following message appears on the
panel display for approximately 15 minutes while the machine is
being warmed up.
Setting Up...
[ >
ZESX332E
Setting Up...
[ > >
Setting Up...
[ > > >
Setting Up...
[ > > > >
Setting Up...
[ > > > > > ]
ZESX333E
After the machine warms up, "Ready" appears on the panel display.
Ready
Press {Menu}.
On Line
Menu
Job Reset
Form Feed
Power
The following message appears on the panel display.
Menu:
Paper Input
Press { } or { } to display "Language".
Menu:
Language
Press {Enter #}.
The following message appears on the panel display.
Language:
*English
Press { } or { } to display the language you
want to select.
Press {Enter #}.
"Menu" appears on the panel display.
Menu:
Paper Input
Press {On Line}.
"Ready" appears on the panel display.
Ready
ZESX335E
PRINTING THE TEST PAGE
]
You can check if the printer works properly by
printing a test page such as the configuration page.
However, you cannot check the connection
]
between the printer and the computer by printing
the test page.
]
Turn on the printer if it is not already on.
]
It takes time before the machine warms up. See
THE PANEL DISPLAY LANGUAGE".
After the machine warms up, "Ready" appears on the panel display.
Ready
Escape
#
Enter
Error
Data In
Press {Menu}.
ZDJS100N
Menu:
Paper Input
Press { } or { } to display "List/Test Print".
Menu:
List/Test Print
Press {Enter #}.
The following message appears on the panel display.
List/Test Print:
Config.Page
Confirm that "Config.Page" is on the display, and
then press {Enter #}.
In a short time, the test printing will start.
Printing...
Important
If you cannot complete the test printing correctly,
see if an error message appears on the panel display.
For more information about error messages, see
"Troubleshooting" in Maintenance Guide 2 on the
CD-ROM labeled "Operating Instructions".
Press {On Line}.
"Ready" appears on the panel display.
Ready
Press {Menu}.
Print the sheet for checking the color condition to confirm the
development units are properly installed.
Press { } or { } to display "Maintenance"
on the panel display, and then press {OK}.
Menu:
Maintenance
Press { } or { } to display "Devp.Unit Check"
on the panel display, and then press {OK}.
Menu:
Devp.Unit Check"
The following message appears on the panel display.
Press #to test
print Devp.Unit
Press {OK}.
Print out the sheet for checking the color condition.
Printing...
ZESX335E
"SELECTING
KCMY
Development Unit Test Print
YMCK
Print Quality Sample
1. Check that all colors are printed on the Test Sheet with no line breaks in them.
2. Reset the Development Unit(s) for colors where line breaks have occurred.
3. Repeat the Devp. Unit Check test print, then check the sheet again.
Color-01
Use the sheet to check the print quality of each
color.
If the printed sheet has no broken or blurred colors, the development
units are installed properly. If this is not the case, reset the
Development Unit(s) for colors where line breaks have occurred by
pulling out the unit partially, and then inserting it slowly. After
resetting the Development Unit(s), print out this sheet again and
re-check the print quality.
CONNECTING THE PRINTER TO
A COMPUTER
Connecting the printer to a computer using
a network interface cable.
Confirm that the printer's power switch is off. If it
is on, turn it off.
ZESX332E
Loop the network interface cable and attach the
ferrite core.
Note
The network interface cable loop should be about
15 cm (6") ( ) from the end of the cable (on the
end closest to the printer).
Connect the network interface cable to the
ethernet port on the back of the printer.
Connect the other end of the cable to the network
such as hub.
Turn on the printer.
Confirm the LEDs on the ethernet port.
ZESX338E
is lit when 100 BASE-TX is in use and not lit when 10 BASE-T is
in use.
is lit when the printer is securely connected to the network.
Go to
"CONFIGURING THE PRINTER FOR
THE NETWORK".