Cisco WAP2000 Hızlı Başlangıç Kılavuzu

Kablosuz Erişim Noktası Cisco WAP2000 için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Cisco WAP2000 2 sayfaları. Wireless-g access point with power over ethernet

Sayfayı Yazdır

Quick Start Guide

Cisco Small Business

WAP2000 Wireless-G Access Point with Power

Over Ethernet

Package Contents

• Wireless-G Access Point with Power Over Ethernet

• Detachable Dipole Antennas (2)

• Power Adapter

• Ethernet Cable

• CD-ROM

• Quick Start Guide

Welcome

Thank you for choosing the WAP2000 Wireless-G Access Point with Power

Over Ethernet. The access point features RangeBooster technology that is

compatible with standard 802. 1 1g but with a range up to two times further and

throughput up to 35 percent faster. Unlike ordinary wireless technologies that

are hampered by wireless signals that reflect off walls, ceilings, and other

objects, RangeBooster uses these multiple signals with two smart receivers at

each end (router or access point and client adapter) to boost range and

throughput speeds. As a result, a RangeBooster solution reduces or eliminates

wireless signal dead spots in offices and other buildings so users can connect

to the network in more areas.

This guide describes how to physically install your WAP2000 and how to set

up a basic configuration by using the configuration utility.

Before You Begin

Before you begin the installation, make sure that you have the following

equipment and services:

• Tools for installing the hardware

• Category 5e Ethernet cable

• PC with Microsoft Internet Explorer (6.0 or later) or Mozilla Firefox for using

the web-based system management tools

• A Cisco Small Business Power over Ethernet (PoE) switch or a switch and a

802.3af compliant power injector

• (

Recommended

) Uninterruptible Power Supply (UPS) to provide backup

power to essential devices

Getting to Know the WAP2000

This section describes the external features of the WAP2000.

Front Panel

POWER—(Green) Lights up when the access point is powered on.

PoE—(Green) Lights up when the access point is powered through an

Ethernet cable.

WIRELESS—(Green) Lights up when the wireless module is active on the

access point. The LED flashes when the access point is actively sending or

receiving data from a wireless device.

Ethernet—(Green) Lights up when the access point successfully connects to

a device through the Ethernet network port. This LED flashes when the access

point is actively sending to or receiving data from one of the devices over the

Ethernet network port.

Back Panel

Antenna Ports—The access point has two antenna ports for connecting

detachable 3 dBi omnidirectional antennas. Adjust the two antennas so that

they form a 90 degree angle for best MIMO range performance.

RESET Button—There are two ways to reset the access point to the factory

default configuration. Either press the Reset button for more than ten seconds

or restore the defaults using the web-based utility of the access point. If you

press the Reset button for less than ten seconds, the access point will simply

reboot.

ETHERNET Port—Connects to Ethernet network devices, such as a switch or

router. The access point can be powered using Power over Ethernet.

POWER Port—Connects the access point to power using the supplied power

adapter. Use this option if your switch or router doesn't support Power over

Ethernet.

Side Panel

Security Slots—The security slots can be utilized to attach a lock to the

access point.

Installing the WAP2000

You can place your WAP2000 on a desktop or mount it on a wall.

Placement Tips

• Ambient Temperature—To prevent the WAP2000 from overheating, do not

operate it in an area that exceeds an ambient temperature of 131°F (55°C).

• Air Flow—Be sure that there is adequate air flow around the WAP2000.

• Mechanical Loading—Be sure that the WAP2000 is level and stable to

avoid any hazardous conditions.

• Power Outlet—Choose a location that is within reach of a power outlet.

Wall Mounting

The WAP2000 can be mounted either vertically or horizontally.

Determine where you want to mount the access point and install two

TEP

screws (not supplied) into the wall for either vertical or horizontal

placement.

For horizontal placement, orient the access point as shown:

5-7/8˝

Wall

mount

slots

For vertical placement, orient the access point as shown:

4-1/4˝

Wall

mount

slots