Cisco EX90 Hızlı Referans Kılavuzu - Sayfa 2

Konferans Sistemi Cisco EX90 için çevrimiçi göz atın veya pdf Hızlı Referans Kılavuzu indirin. Cisco EX90 2 sayfaları. Telepresence system
Ayrıca Cisco EX90 için: Kullanıcı Kılavuzu (50 sayfalar), Kullanıcı Kılavuzu (37 sayfalar), Kullanıcı Kılavuzu (49 sayfalar), Hızlı Referans Kılavuzu (2 sayfalar), Başlangıç Kılavuzu (42 sayfalar), Kullanıcı Kılavuzu (45 sayfalar), Kurulum Kılavuzu (6 sayfalar), Hızlı Referans Kılavuzu (2 sayfalar), Kullanıcı Kılavuzu (7 sayfalar), Sorun Giderme Kılavuzu (37 sayfalar), Kurulum Kılavuzu (2 sayfalar), Kullanıcı Kılavuzu (45 sayfalar), Kullanıcı Kılavuzu (37 sayfalar), Başlangıç Kılavuzu (46 sayfalar)

Sayfayı Yazdır
Cisco EX90 Hızlı Referans Kılavuzu
seLFvieW & CAmerA ControL
To check how you appear on the screen,
either tap the Selfview icon (
want to adjust, tap More (
Camera control (
).
Adjust zoom and focus as required. Tap
Back to go exit.
touCh tones (dtmF)
You may be to urged enter touch tones
(DTMF) during a call, typically to reach
extensions or to provide a pin code. Tap
touch
tones.
Tap anywhere outside the pad to exit.
CLeAr history
To clear History,
scroll as outlined
beyond what
appears to be the
top of the list.
A Clear List
button will then
appear.
Copyright © 2010–2012 Cisco Systems, Inc. All rights reserved
Join And trAnsFer
Assume that you are in a call and that
), or if you
someone else calls you.
) followed by
You may now accept and put the current on
hold; accept and end current; decline the
incoming call; or just ignore it.
If you put someone on hold, tapping
resume will enable you to:
•
Tap Swap to put the other on hold
instead.
•
Tap transfer to connect the one on
hold to somebody else.
•
Tap Join to include the one on hold in
the current call in order to turn it into a
conference, or to expand an ongoing
conference. This is an optional feature,
that, if available, will act in lieu of
the optional conferencing feature
described overleaf.
Note that if you have set up a conference
by means of the Join feature, each
participant must actively disconnect own
equipment when the conference is over.
You may deactivate the microphone for
privacy reasons, if needed (
Tap as outlined (
volume.
When set to Do Not Disturb, ringtones are
muted and incoming calls are shown as
missed calls when you deactivate it. You may,
however, place calls as much as you like. To
activate this feature, press the icon in the
upper left corner. Press again to deactivate.
You may also hide the Do Not Disturb poster
by tapping Hide.
sound mAtters
).
) to adjust the sound
do not disturb
shAring PresentAtions
In a call, you may share a source connected
to your video system.
To share a source, make sure the source
is connected and active. Otherwise, the
Presentation button will not appear.
Tap Presentation (
). Then tap Present
(
) to start sharing contents.
Tap Present followed by Stop Presenting
to stop sharing contents.
LAyout ControL
In MultiSite and in Point-to-Point calls
with presentation running, you may alter
the layout on the screen. Tap More (
followed by Layout (
).
Select your preferred layout.
ringtones & sounds
To set ringtones and sound, tap More
(
) followed by Settings (
ringtone & Sound Settings (
Set Keytones to On or Off, the ringtone
volume and select the ringtone of your
choice. Tap Exit to go back.
D14743.05 TC 5.1 Feb. 2012
)
). Then tap
).