ACU-RITE Iris 06014 Kullanım Kılavuzu - Sayfa 6

Hava İstasyonu ACU-RITE Iris 06014 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. ACU-RITE Iris 06014 20 sayfaları. (5-in-1) weather sensor (dual solar panel)

Sayfayı Yazdır

Calibrate the Rain Gauge

The rain gauge on the AcuRite Iris sensor can be calibrated to improve accuracy.

Items Needed: AcuRite Iris sensor, companion unit, plastic cup, pin, screw driver

1. First, ensure AcuRite Iris sensor is perfectly level using built-in bubble level.

2. Use compatible companion unit or AcuRite software to monitor during calibration.

3. Make a pin hole in the bottom of a plastic cup. Hold the cup over the rain gauge and fill it with exactly

1 cup (8oz) of water, allowing the water to drip into the rain gauge. You should hear the internal buckets

tip and see water drain through the rain gauge.

4. A few seconds after each bucket tip, the companion unit displays rainfall in approximately 0.01" or

more increments.

5. The cup of water should take more than 20 minutes to empty; a quicker period will result in inaccurate

calibration. Try to simulate a normal steady rainfall. When cup is empty of water, companion unit should

Tips

• There should be nearly an equal number of water drops (about 25 water drops) between bucket tips. If

not, adjust the calibration screws on the bottom of the AcuRite Iris sensor until an equal number of water

drops are tipping the buckets.

Adjustment

If the rain gauge doesn't register close to 1.06", make an EQUAL adjustment to the two calibration screws

on the bottom of the AcuRite Iris sensor. Turning screws clockwise increases rainfall; counter clockwise

decreases rainfall.

•To adjust the rainfall reading by 2% turn both screws 1/8 of a turn.

•To adjust the rainfall reading by 4% turn both screws 1/4 of a turn.

•To adjust the rainfall reading by 8% turn both screws 1/2 of a turn.

Specifications

TEMPERATURE RANGE

HUMIDITY RANGE

WIND SPEED

WIND DIRECTION INDICATORS

RAINFALL

WIRELESS RANGE

OPERATING FREQUENCY

POWER

DATA REPORTING

FCC Information

This device complies with part 15 of FCC rules. Operation is subject to the

following two conditions:

1- This device may NOT cause harmful interference, and

2- This device must accept any interference received, including interfer-

ence that may cause undesired operation.

WARNING: Changes or modifications to this unit not expressly approved

by the party responsible for compliance could void the user's authority to

operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

Outdoor: -40ºF to 158ºF; -40ºC to 70ºC

Outdoor: 1% to 99%

0 to 99 mph; 0 to 159 kph; 0 to 86 knots

16 points

0.01 inches (0.25 mm) and up

330 ft / 100 m

depending on home construction materials

433 MHz

4 x AA alkaline or lithium batteries

Wind Speed: 18 second updates; Direction: 30 second updates

Outdoor temperature & humidity: 36 second updates

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

NOTE: The manufacturer is not responsible for any radio or TV interfer-

ence caused by unauthorized modifications to this equipment. Such

modifications could void the user authority to operate the equipment.

This device complies with Industry Canada licence-exempt RSS

standard(s).

Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference received, including interfer-

ence that may cause undesired operation of the device.