Cisco TelePresence Kurulum Kılavuzu

Konferans Sistemi Cisco TelePresence için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Cisco TelePresence 4 sayfaları. Configuring a cisco unified communications manager sip trunk with a cisco telepresence content server
Ayrıca Cisco TelePresence için: Broşür (4 sayfalar), Teknik Özellikler (7 sayfalar), Yönetici El Kitabı (27 sayfalar), Hızlı Referans Kılavuzu (2 sayfalar), Manuel (24 sayfalar), Kurulum Sayfası (2 sayfalar)

Sayfayı Yazdır

Installing Cisco TelePresence System Profile 65"

PROfILE 65" IS DELIvERED WITH:

Monitor

Column

Foot module (stand-alone or wall stand)

Grille

Camera

Touch 8" interface device

Remote control

Microphones

Accessories

Unpacking the foot module

Lift out to open

the snap lockers.

fOOT MODULE (25 kG / 55 LbS)

Open the snap lockers

HEAvY

CAUTION

Lift out the foot module box

Mounting the column to the foot module to complete the bottom module

PERSON 1:

Lift here.

MOUNTING THE BOTTOM MODULE

PERSON 2:

Lift here.

Front

When the bottom module is finished,

the hole in the foot module should be

visible on the rear side only.

The illustration shows the stand-alone

foot module. The wall stand foot module

is mounted in the same way.

PRECAUTIONS

Follow the steps in this installation guide when unpacking and

assembling the Profile 65".

A minimum of four (4) persons are required during the installation of the

system.

• The monitor box requires four (4) persons to lift.

• The column requires two (2) persons to lift.

• The foot module requires two (2) persons to lift.

NOTE:

The floor must be in level.

WEIGHTS Of THE DIffERENT UNITS (PACKAGING INCLUDED)

• Monitor box: 110 kg / 243 lbs

• Column: 40 kg / 88 lbs

• Foot module box: 25 kg / 55 lbs

• Accessories, camera, Touch 8" and grille boxes: 8 kg / 17.6 lbs

STAND-ALONE FOOT MODULE

Front

WALL STAND FOOT MODULE

Rev. Date

Prep.

Checked Change

Telecom AS

Sheet 1 of 1

Processes

Tolerances

Specification:

Front

Type:

European

Manufacturer:

117000 rev.

projection

Type number:

Thickness:

Eagle

Unit:

Dimensions without paint or finish

Color:

Sheet size:

Surface:

All materials, finishes, and proccesses

Glossiness:

Scale:

1:10

must comply with the RoHS directives

Flame class:

3D CAD model file 117000

rev. 00Z+ is master

Part weight:

108964g

Flame class requirement: -

UL reference:

ACCESSORIES TO THE fOOT MODULE

• Orange level adjustment tool

• 4 × Nuts

Rev. Date

Prep.

Checked Change

• Wall brackets (wall stand only)

Sheet 1 of 1

Processes

Tolerances

Specification:

Material

Telecom AS

Type:

European

Manufacturer:

117000 rev.

projection

Type number:

• Spacer (wall stand only)

Thickness:

Eagle

Unit:

Dimensions without paint or finish

Color:

Sheet size:

All materials, finishes, and proccesses

Surface:

must comply with the RoHS directives

Glossiness:

• Allen key (wall stand only)

Scale:

1:10

Flame class:

3D CAD model file 117000

rev. 00Z+ is master

Part weight:

108964g

Flame class requirement: -

UL reference:

Lift the column and place it carefully

on the foot module.

When looking down through the

column you can see the four screws

in the foot module.

Make sure the screws enter the

corresponding holes in the column.

Open the front door to access the

screws. Secure the column to the

foot module with four nuts. The nuts

are found in the plastic bag. See the

illustration to the right.

Fasten the 4 nuts

(two on each side

of the system).

UNPACKING THE SYSTEM AT THE DESTINATION

It is highly recommended to start the unpacking and assembling of

Profile 65" at the place where the system is to be used.

Check the dimensions of the lift if you need to use a lift for the

transportation.

Outer dimensions and total weight of the main unit (package included):

• Height: 145 cm / 57.1 in.

• Width: 76 cm / 29.9 in.

• Length: 170 cm / 66.9 in.

• Weight: 183 kg / 402 lbs

NOTE:

If it is not possible to bring the main unit to the destination,

follow step 1–2 and bring the smaller units to the destination.

Unpacking the unit

Lift out to open

the snap lockers.

Material

Surface treatment

Place the unit on a stable surface.

Open the snap lockers to remove

outer cover.

Locate the different parts.

Lift out the camera, Touch 8",

grille and accessories boxes.

Surface treatment

Remove the packaging above and

around the column and monitor

box.

The illustration shows

a cross section of

the bottom module

(column and foot

module).

Page 1

DIMENSIONS (WHEN ASSEMBLED)

The Profile 65" system has the following dimensions:

• Height: 167 cm / 65.7 in.

• Width: 153 cm / 60.3 in.

• Depth: Stand-alone: 66 cm / 26 in.

USER DOCUMENTATION

User guides and compliance and safety information for this product are

available on the Cisco web site:

The Video conferencing room primer and Video conferencing room

acoustics guidelines documents contain information about optimizing a

meeting room for video conferencing.

Monitor box

Outer cover

Grille box

Touch 8" box

Accessories box

Camera box

Foam to protect

the column

Column

Key lock and levelling adjustment

The level adjustment tool is found in

the foot module box. The key lock

tool is found in the accessories box.

Lock

Unlock

KEY LOCK

Place the orange key on the key

lock and turn clockwise to lock,

counterclockwise to unlock.

Wall stand, with short bracket: 44.7 cm / 17.6 in.

Wall stand, with long bracket: 52.2 cm / 20.6 in.

http://www.cisco.com/go/profile-docs

MONITOR bOX

COLUMN

(110 kg / 243 lbs)

(40 kg / 88 lbs)

HEAvY

AND

BULKY

REQUIRES:

4 PEOPLE TO LIfT

2 PEOPLE TO LIfT

CAUTION

ACCESSORIES BOX

• Power cables

• Wrench

• Microphones

• key lock tool

• Remote control

• Gloves

• batteries

• Cleaning cloth

ADJUST UP

Place the level adjustment tool as

illustrated. Seen from above, turn

clockwise to adjust the height up.

ADJUST DOWN

Place the level adjustment tool at

the opposite side of the wheel.

Turn counterclockwise to adjust

the height down.