Argo DD Series Kullanım Talimatları Kılavuzu - Sayfa 6

Klima Argo DD Series için çevrimiçi göz atın veya pdf Kullanım Talimatları Kılavuzu indirin. Argo DD Series 15 sayfaları. Air conditioner without outdoor unit

Sayfayı Yazdır

HOW TO SET THE PRESENT TIME

EN
1. Press the button ST three times.
The time indication alone flashes.
2. Press the H button until the present time hour is
displayed. Press the M button until the present time
minutes are displayed. The display will automatically
stop flashing.

COOLING

NOTE
Verify that the unit is connected to the
main power.
1. Set the
selector to COOL (symbol
on the display).
2. Press the +/- buttons (temperature
selection) to set the desired temperature
(the temperature range is between 32 °C
max. and 10 °C min.).
THE DISPLAY SHOWS THE
SELECTED TEMPERATURE.
3. Press the FAN button to select the fan speed.

HEATING

1. Set the
selector to HEAT (fixed or flashing
on the display.
2. Press the +/- buttons (temperature selection) to set the
desired temperature (the temperature range is between 32
°C max. and 10 °C min.).
THE DISPLAY SHOWS THE
SELECTED TEMPERATURE.
3. Press the FAN button to select the fan speed.
NOTE
For several minutes after the start of heating operation, the
indoor fan will stop until the indoor heat exchanger coil has
warmed up sufficiently. This is because the COLD DRAFT
PREVENTION SYSTEM is operating. During this period,
the STANDBY lamp remains lit.
DEFROSTING OF OUTDOOR UNIT HEAT
EXCHANGER
When the outdoor temperature is low, frost or ice may
appear on the heat exchanger coil, reducing the heating
performance. When this happens, a protection function
for the heat exchanger defrosting is activated. During this
function operation, the fan of the indoor unit stops. Heating
operation restarts after several minutes. (This interval
will vary slightly depending on the room and outdoor
temperature).
C
1
2
3
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE SETTING
THE DISPLAY WILL SHOW THE ROOM
TEMPERATURE AGAIN.
symbol
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE SETTING
THE DISPLAY WILL SHOW THE ROOM
TEMPERATURE AGAIN.

AUTOMATIC OPERATION

1. Set the
or
the display.
2. Press the +/- buttons (temperature selection) to set the
desired temperature (the temperature range is between
32 °C max. and 10 °C min.).
THE DISPLAY SHOWS THE
SELECTED TEMPERATURE.
When this setting is selected, the air conditioner calculates
1
the difference between the thermostat setting and the
room temperature and automatically switches to the
2
COOL or HEAT mode as appropriate.
3. Press the FAN selector button to the setting you want.
Example of operation diagram in the
with the set room temperature at 23°C.
27
A
26
25
B
24
C
23
C
22
21
B
20
A
19
ON
NOTE
The air conditioner changes the operation mode (from cool
to heat or vice versa, if one of the following conditions
occurs:
- ZONE A: changes if the difference between the room
temperature and the temperature set on the remote
control unit is at least 3°C.
- ZONE B: changes if the difference between the room
temperature and the temperature set on the remote
control unit is at least 1°C, one hour after the compressor
stop.
- ZONE C: never changes if the difference between the
room temperature and the temperature set on the remote
control unit is no more than 1°C.

DEHUMIDIFYING (DRY)

1. Set the
button to DRY. The icon
2. Press the +/- buttons (temperature selection) to set the
desired temperature (the temperature range is between
32 °C max. and 10 °C min.).
THE DISPLAY SHOWS THE SELECTED
TEMPERATURE.
6
selector to AUTO (symbol
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE SETTING
THE DISPLAY WILL SHOW THE ROOM
TEMPERATURE AGAIN.
(Auto) mode
D
1
H
D
1
H
ON
MIN.
MAX.
is displayed.
AFTER 5 SECONDS FROM THE REQUIRED
TEMPERATURE SETTING THE DISPLAY WILL
SHOW THE ROOM TEMPERATURE AGAIN.
on
ON