Sony 10001 Kurulum Kılavuzu - Sayfa 8
Video Kamera Sony 10001 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Sony 10001 28 sayfaları. A/v multiplexer board, a/v demultiplexer board
Ayrıca Sony 10001 için: Kurulum Kılavuzu (50 sayfalar)
Sayfayı Yazdır
1-2. Information of BKPF-105A
1-2-4. Location and Function of Switches/
LEDs
AVM-6 board
1
2
3
4
5
6
7
1
1
1 D511 and D512 : AUDIO EXIST indicators
1
1
These indicators indicate the existence of an AES/
EBU digital audio input signal. They light in green
when an input signal exists.
D511
Group 1
1/2 CH
Group 2
5/6 CH
2
2
2
2
2 D513 and D514 : AUDIO ERROR indicators
These indicators indicate the error of an AES/EBU
digital audio input signal. They light in red when an
input signal is not in synchronization with an audio
clock and an error occurs.
D513
Group 1
1/2 CH
Group 2
5/6 CH
3
3 S501 : Mode set switch (8-poles DIP switch)
3
3
3
Factory settings : All "OFF" side
S501-1 : D1/D2 system select switch
This switch selects the system of the video signal.
D1 : 4:2:2 component serial digital video signal
D2 : 4fsc composite serial digital video signal
S501-2 : Audio group select switch
This switch selects the group number of the audio data
to be multiplexed.
1-4(E)
8
!/
9
Component side (A side)
D512
3/4 CH
7/8 CH
D514
3/4 CH
7/8 CH
In D1 mode
GP1 : Group 1
The DID in a signal is set to audio group 1.
The AES/EBU digital audio input signal is multiplexed
as 1 CH through 4 CH in an SDI signal. If audio data
has been already multiplexed into the input SDI signal,
the input digital audio signal is multiplexed after all
audio data are erased.
GP2 : Group 2
The DID in a signal is set to audio group 2.
The AES/EBU digital audio input signal is multiplexed
as 5 CH through 8 CH in an SDI signal. If audio data
has been already multiplexed into the input SDI signal
and the DID of audio data has been set to audio group 1,
the digital audio signal is multiplexed later than the
audio data. When the data of audio group 1 is not
detected, D705(MULTIPLEX ERROR indicator) lights
in red and the audio data is not multiplexed.
In D2 mode
GP1 : Group 1
The DID in a signal is set to audio group 1.
The AES/EBU digital audio input signal is multiplexed
as 1 CH through 4 CH in an SDI signal. If audio data
has been already multiplexed into the input SDI signal,
the input digital audio signal is multiplexed after all
audio data are erased. In D2 mode, the DID is usually
set to audio group 1.
GP2 : Group 2
The DID in a signal is set to audio group 2.
The AES/EBU digital audio input signal is multiplexed
as 5 CH through 8 CH in an SDI signal. If audio data
has been already multiplexed into the input SDI signal,
the input digital audio signal is multiplexed after all
audio data are erased. In D2 mode, only one group can
be multiplexed at a time. The DID is not set to audio
group 2 usually.
S501-3 : Factory use only
Keep as the default setting.
BKPF-105A/205/205R
BKPF-106A/206/206R