Cisco 2800 Series Hızlı Başlangıç Kılavuzu - Sayfa 16

Ağ Donanımı Cisco 2800 Series için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Cisco 2800 Series 45 sayfaları. Cisco ios software configuration
Ayrıca Cisco 2800 Series için: Hızlı Başlangıç Kılavuzu (13 sayfalar), Veri Sayfası (8 sayfalar), Hızlı Başlangıç Kılavuzu (47 sayfalar), Uygulama Notu (41 sayfalar), Konfigürasyon (10 sayfalar), Genel Bakış (27 sayfalar), Veri Sayfası (5 sayfalar), Veri Sayfası (20 sayfalar), Yapılandırma (32 sayfalar)

Cisco 2800 Series Hızlı Başlangıç Kılavuzu
Figure 11
Attaching the Cable Management Bracket to the Cisco 2811 Router
EN M0
Either edge may go up. Attach
Wall-Mounting the Router—Cisco 2811 Routers Only
You can mount a Cisco 2811 router on a wall. Cisco 2801, Cisco 2821, and Cisco 2851 routers are not designed for
wall-mounting.
Warning
This unit is intended to be mounted on a wall. Please read the wall mounting instructions carefully before
beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a
hazardous situation to people and damage to the system. Statement 248
To attach a Cisco 2811 router to a wall or other vertical surface, use the 23-inch (58.42-cm) rack-mount brackets to attach the
router to the wall as described in the following sections.
Attaching Brackets to the Router for Wall Mounting
Attach the standard brackets to the chassis as shown in Figure 12, using the four screws provided for each bracket.
Figure 12
Attaching the Brackets for Wall-Mounting a Cisco 2811 Router
SY S
AU X/
PW R
SY S
PW R
AC T
CF
CO NS OL
CO MP AC
T FLA SH
1
E
OP TIO NA
WA RN ING
Do Not Rem
0
mu st be
ove Dur ing
equ ipm ent
Net wor k
AU X
Op era tion
and an RP
Attaching the Router to a Wall
Attach the router to the wall using the brackets previously attached and attachment hardware that you provide as follows:
• For attaching to a wall stud, each bracket requires two #10 wood screws (round- or pan-head) with #10 washers, or two
#10 washer-head screws. The screws must be long enough to penetrate at least 3/4 inch (20 mm) into supporting wood or
into a metal wall stud.
• For hollow-wall mounting, each bracket requires two wall anchors with washers. Wall anchors and washers must be size
No. 10.
16
S
L
O
T
3
S
S
L
O
L
O
T
T
1
A= AC T
2
A= FDX
A
S= SPE ED
A= LIN K
FE 0/1
F
FE 0/0
S
S
L
O
L
T
0
PVD M1
PVD M0
AIM 1
Cable management bracket.
to either side of the chassis.
L RP S INP
UT
-- RP S cov
er
ins tall ed
wh en
is wa ll-m
oun ted
S is not
con nec ted
12V
11A
-48 V
4A
100 -24 0
V~ 4A
50/ 60 Hz
A
F
S
L
AIM 0
Screws from
accessory kit