Cisco 7606 Kullanıcı Kılavuzu - Sayfa 15

Ağ Donanımı Cisco 7606 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Cisco 7606 28 sayfaları. User guide
Ayrıca Cisco 7606 için: Broşür (8 sayfalar)

Sayfayı Yazdır

1. Catalyst 6509 Switch and Cisco 7606 and Cisco 7609 Routers

Installing the Opacity Shield on the Cisco 7600 Series Routers

This section describes how to install the opacity shield on the Cisco 7606 router. The opacity shield,

associated installation hardware, and tamper evidence labels are part of the Cisco 7600 FIPS kit

(part number CVPN7600FIPS/KIT=). The opacity shield is designed to be installed on the Cisco 7606

router while the system is operating without creating an electrical hazard or damage to the system. You

will need some clearance between adjacent racks in order to perform this procedure.

The opacity shield is not required for the Cisco 7609 router chassis. The Cisco 7609 router chassis

satisfies the FIPS opacity requirement without an external shield.

To install an opacity shield on the Cisco 7606 router chassis (see

Step 1

The opacity shield is designed to be installed on a Cisco 7606 chassis that is already rack-mounted. If

your Cisco 7606 chassis is not rack-mounted, install the chassis in the rack using the procedures

contained in the Cisco 7600 Series Router Installation Guide. If your Cisco 7606 chassis is already

rack-mounted, proceed to step 2.

Open the FIPS kit packaging (part number CVPN7600FIPS/KIT=). The kit contains the following:

Step 2

•

Remove the opacity shield from its protective packaging.

Step 3

Note

Start the two thumbscrews in the corresponding threaded holes in the opacity shield (see

Step 4

or three turns is sufficient. Do not thread the thumbscrews too far into the opacity shield.

Open the envelope containing the disposable ESD wrist strap. Attach the disposable ESD wrist strap to

Step 5

your wrist. Attach the other end of the wrist strap to exposed metal on the chassis.

Position the opacity shield over the air intake side of the chassis so that the two thumbscrews on the

Step 6

opacity shield are aligned with the unused top and bottom L-bracket screw holes on the chassis.

Press the opacity shield firmly against the side of the chassis and secure the opacity shield to the chassis

Step 7

with the two thumbscrews.

OL-6334-01

An opacity shield assembly for the Cisco 7606 router (part number 800-26211-xx). The opacity

shield part number is located on the outside of the protective packaging.

A bag containing the installation hardware (In some kits there is no bag; the installation hardware

is premounted in the opacity shield.

An envelope with 30 FIPS tamper evidence labels and a disposable ESD wrist strap.

If the thumbscrews and the snap rivet fasteners are already installed on the opacity shield, remove

the four snap rivet fasteners from the opacity shield; leave the thumbscrews installed. Proceed to

step 5.

Verify that the thumbscrews are started only two or three turns in the opacity shield.

If the opacity shield comes with a bag of installation hardware (69-1483-xx), open the bag and

remove the two thumbscrews and four snap rivet fasteners. The snap rivet fasteners come assembled;

you need to separate the two pieces of the snap rivet fastener by removing the snap rivet pin from

the snap rivet sleeve before you install them. Proceed to step 4.

Extra snap rivet fasteners are included in the bag of installation hardware in case of loss or

damage.

Catalyst 6509 Switch, Cisco 7606 Router, and Cisco 7609 Router with VPN Services Module Certification Note

Installing the Opacity Shield on the Cisco 7600 Series Routers

Figure

6), follow these steps:

Figure

6); two