Sony STR-DA2800ES Etkinleştirme Kılavuzu - Sayfa 6
Stereo sistemi Sony STR-DA2800ES için çevrimiçi göz atın veya pdf Etkinleştirme Kılavuzu indirin. Sony STR-DA2800ES 7 sayfaları. Control4 automation
Ayrıca Sony STR-DA2800ES için: Sınırlı Garanti (1 sayfalar), Hızlı Kurulum Kılavuzu (2 sayfalar), Hızlı Kurulum Kılavuzu (2 sayfalar)
Sayfayı Yazdır
See the Control4 Composer Pro User Guide for
more information about how to use the Control4
system.
Configure ZigBee
The ZigBee radio for the Sony STR receiver is
included in a USB Adapter (UWA-C4Z, also known as
a 'ZigBee dongle').
• If the receiver is used as the ZigBee Access Point
(ZAP), ZigBee Coordinator, or to run ZigBee
Server, you must install the ZigBee dongle.
• If ZigBee is provided via another controller,
installing the ZigBee dongle is not necessary.
NOTE: This adapter is not a WiFi adapter or
antenna. If the user's cabinet or rack does
not include enough room for the USB ZigBee
Wireless Adapter, you may want to use a USB
extension cable to relocate the ZigBee dongle
to a more convenient location.
To install the USB ZigBee dongle:
1
Make sure the receiver is turned off and
unplugged from power before installing the
ZigBee dongle.
2
Insert the ZigBee dongle into the USB port on
the back of the receiver, plug in the receiver,
press the power button, and then wait five (5)
minutes. At this point, ZigBee devices can be
identified.
3
To identify ZigBee devices into the project using
Composer Pro, a ZigBee mesh must exist in your
project (see the Control4 Knowledgebase to
learn how to create a mesh). After you've created
the mesh, you can identify and Control ZigBee
devices in the Control4 system.
Configure Receiver Only
NOTE:
If your customer intends to use the
Sony STR receiver (ZSO-STRDA2800ES
or ZSO-STRDA5800ES) as a receiver only
in a Control4 system, refer to the Sony
documentation on the Sony website and the
Composer Pro User Guide at www.control4.
com. You will need to add the Sony STR-
DA5800ES or STR-DA2800ES Certified driver
from the online driver database and identify
the device in Composer Pro.
6
Troubleshooting
Factory Resets or Restores
To perform a factory reset:
1
On the front of the receiver, press the Power
button to turn the receiver off.
2
While holding down the TONE and the
2CH/A Direct buttons on the front of the receiver,
turn the receiver back on by pressing the Power
button again. The receiver reset begins when
the "Memory Clearing" message displays in
the DA5800ES's front window. The DA2800ES
displays a "Clearing..." message in the front
window.
3
When the message displays, release the buttons.
The reset process may take up to 20 minutes before
the receiver display returns to normal (please be
patient).
CAUTION!
(1) All project information is erased during
a factory reset. Re-register and identify the
receiver again after the reset.
(2) If the factory reset does not work, contact
Control4 Technical Support for additional
information.
Reboots
Powering off the Sony STR receiver using the Power
button on the front of the receiver will not reboot the
Control4 automation functions; unplug the receiver to
completely reboot the system.
Regulatory/Safety
and Other Information
To review regulatory information for your particular
Control4 products, see the information located on
the Control4 website at: http://www.control4.com/
regulatory/.