Sony STR-DA80ES - Fm Stereo / Fm-am Receiver Kullanım Talimatları Kılavuzu - Sayfa 16
Stereo sistemi Sony STR-DA80ES - Fm Stereo / Fm-am Receiver için çevrimiçi göz atın veya pdf Kullanım Talimatları Kılavuzu indirin. Sony STR-DA80ES - Fm Stereo / Fm-am Receiver 40 sayfaları. Limited warranty (es products)
Ayrıca Sony STR-DA80ES - Fm Stereo / Fm-am Receiver için: Kullanım Talimatları Kılavuzu (39 sayfalar), Teknik Arka Plan (38 sayfalar), Sınırlı Garanti (1 sayfalar)
Sayfayı Yazdır
Receiver Operations
z
If the STEREO indicator remains off
Press FM MODE even when an FM stereo broadcast is
received.
z
If an FM stereo program is distorted
The STEREO indicator flashes. Press FM MODE to
change to monaural (MONO). You will not have the
stereo effect but the distortion will be reduced. To
return to the auto stereo mode, press this button again.
z
If you cannot tune in a station and the entered
numbers are flashing
Make sure you've entered the right frequency. If not,
press D.TUNING and reenter the frequency you want.
If the entered numbers still flash, the frequency is not
used in your area.
z
To watch FM simulcast TV programs
Make sure that you tune in the simulcast program on
both the TV (or VCR) and the receiver.
z
If you enter a frequency not covered by the tuning
interval
The entered value is automatically rounded up or down
to the closest covered value.
Tuning intervals for direct tuning are:
FM: 50 kHz intervals
AM: 10 kHz intervals (USA and Canadian models only;
to change to 9 kHz intervals, see page 32.)
9 kHz intervals (Australian model only)
9 kHz intervals (models for all other countries; to
change to 10 kHz intervals, see page 32.)
Receiving broadcasts by scanning stations
(automatic tuning)
If you don't know the frequency of the radio station
you want, you can have the receiver scan all the
receivable stations to locate the one you want.
1
Rotate FUNCTION until the TUNER indicator
lights up.
The last received station is tuned in.
2
Press DISPLAY so that the frequency appears in
the display.
3
Press FM/AM to select FM or AM.
4
Press TUNING + or –.
Press the + button for a higher station number;
press the – button for a lower one. When you tune
past either end of the band, the receiver
automatically jumps to the opposite end and
continues scanning in the same direction. Every
time a station is received, the receiver stops
scanning. To continue scanning, press the button
16
again.
Presetting Radio Stations
You'll most likely want to preset the receiver with the
radio stations you listen to often so that you don't have
to tune in the station every time. The receiver can store
a total of 30 FM or AM stations. You can store the
stations on preset numbers combining 3 characters (A,
B and C) and numbers (0-9). For example, you can
store a station as preset number A1, B6, or C9.
+
–
PRESET TUNING
/
POWER
DISPLAY
VIDEO 1
VIDEO 2
VIDEO 3
LD/DVD
TV/DBS
S-VIDEO
VIDEO
L
AUDIO
R
VIDEO 3
{MEMORY}
FM MODE
TUNING
INPUT
–
SPEAKERS
A
OFF
B
PRESET TUNING
+
A
B
–
+
SHIFT
FM/AM
PHONES
SHIFT
MEMORY
1
Rotate FUNCTION until the TUNER indicator
lights up.
The last received station is tuned in.
2
Tune in the station you want.
If you are not familiar with how to tune in a
station, see "Receiving Broadcasts" on page 15.
3
Press MEMORY.
"MEMORY" appears for a few seconds.
Do Steps 4 and 5 before "MEMORY" goes out.
4
Press SHIFT to select a memory page (A, B or C).
Each time you press SHIFT, the letter "A," "B" or
"C" appear in the display.
5
When using the buttons on the receiver:
Press PRESET +/– to specify the preset number,
and then press MEMORY.
"MEMORY" goes out and the selected station is
preset.
When using the buttons on the remote:
Press the numeric button on the remote (0 to 9).
If "MEMORY" goes out before you specify the
preset number, start again from Step 3.
6
Repeat Steps 2 to 5 to preset other stations.
MUTING
MASTER VOL
SUR
PANEL
EQ
UP/DOWN
INDEX
TAPE
DAT/MD
CD
TUNER
PHONO
EQUALIZER
DPC
SET UP
BALANCE
MODE
•
+
BAND
CH
B
b
0
10
L
R
MODE
FUNCTION
SOUND FIELD
GENRE
MODE
DIRECT
BASS
INPUT
PASS
BOOST
MODE
FUNCTION