Cisco ASR 9906 Manuel - Sayfa 25
Ağ Donanımı Cisco ASR 9906 için çevrimiçi göz atın veya pdf Manuel indirin. Cisco ASR 9906 44 sayfaları. Replacing cisco asr 9000 series router components
Sayfayı Yazdır- 1. Field Replaceable Units
- 2. Online Insertion and Removal
- 3. Powering off the Router
- 4. Replacing the Chassis Air Filter
- 5. Required Tools and Equipment
- 6. Removing a Fan Tray
- 7. Installing a Fan Tray
- 8. Disconnecting AC Power
- 9. Reconnecting AC Power
- 10. Disconnecting DC Power
- 11. Reconnecting DC Power
Replacing Cisco ASR 9000 Series Router Components
Step 3
Install the captive screw in each ejector lever into the screw hole in the power tray frame (figures Rotating
the Ejector Levers Inward to Seat the Version 1 Power Tray or Rotating the Ejector Levers Inward to Seat
the Version 2 Power Tray).
Step 4
Use the 6-inch long number 2 Phillips screwdriver to tighten the two ejector screws to a torque of 10 +/-1
in-lb to secure the ejectors and to secure the tray to its mating connector.
Step 5
Install and tighten two screws through the power tray mounting ears on each side into the screw holes in the
chassis mounting ears to secure the tray to the chassis.
Removing and Replacing Cards from the Chassis
This section describes the procedures for removing and installing an RSP card, RP card, FC, or LC.
See the
information about removing and installing SIP and SPA cards.
• For a information about the router components and slot numbering for the Cisco ASR 9010 Router, Cisco
• For a information about the router components and slot numbering for the Cisco ASR 9922 Router and
• The Cisco ASR 9906 and Cisco ASR 9910 chassis are midplane chassis and the method of removal and
Caution
Handle all cards by the metal card carrier edges only; avoid touching the board or any connector pins. After
removing a card, carefully place it in an antistatic bag or similar environment to protect it from ESD and dust
in the optic ports (fiber-optic line cards).
Caution
Be careful to avoid damaging the EMI gasket that runs along the full height of the card front panel edges.
Damage to the EMI gasket can affect the ability of your system to meet EMI requirements.
Caution
To avoid damaging card mechanical components, never carry an RSP card, RP card, FC, or LC by the captive
installation screws or ejector levers. Doing so can damage these components and cause card insertion problems.
Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide
ASR 9006 Router, and Cisco ASR 9904 Router, see
Cisco ASR 9010 Router, Cisco ASR 9006 Router, Cisco ASR 9904 Router, Cisco ASR 9906 Router,
and Cisco ASR 9910
Router.
Cisco ASR 9912 Router, see
9922 Router and Cisco ASR 9912
replacing cards is different from other routers. The RSP (RSP0, RSP1) cards are located in the front of
the chassis. The 4 line cards on the Cisco ASR 9906 (LC0 - LC3) and 8 line cards on the Cisco ASR
9910 (LC0 - LC7) slots are located in the front of the chassis. The 5 fabric cards (FC0 - FC4) can be
inserted or removed from the rear side of the chassis.
Removing RSP Cards and Line Cards from the
Removing RP Cards, Fabric Cards, and Line Cards from the Cisco ASR
Router.
Replacing Cisco ASR 9000 Series Router Components
Removing and Replacing Cards from the Chassis
for
25