Cisco ASR 9910 Manuel - Sayfa 39
Ağ Donanımı Cisco ASR 9910 için çevrimiçi göz atın veya pdf Manuel indirin. Cisco ASR 9910 44 sayfaları. Replacing cisco asr 9000 series router components
Sayfayı Yazdır- 1. Field Replaceable Units
- 2. Online Insertion and Removal
- 3. Powering off the Router
- 4. Replacing the Chassis Air Filter
- 5. Required Tools and Equipment
- 6. Removing a Fan Tray
- 7. Installing a Fan Tray
- 8. Disconnecting AC Power
- 9. Reconnecting AC Power
- 10. Disconnecting DC Power
- 11. Reconnecting DC Power
Replacing Cisco ASR 9000 Series Router Components
0/RSP0/CPU0
0/RSP1/CPU0
0/FT0
0/FT1
0/1/CPU0
0/FC0
0/FC1
0/FC2
0/FC3
0/FC4
0/PT0
0/PT1
Step 6
Verify RSP in slot 0 and RSP5 in slot 1 reach full synchronization (NSR-ready state) and status of ALL the
groups is Ready state. Use show redundancy command to verify the same.
Step 7
Manually copy Embedded Event Manager (EEM) scripts from RSP to RSP5 disks if applicable.
Note
Step 8
From active RSP, verify the both RSPs have synchronized the SNMP engine ID and SNMP ifindex-table
between each other:
Example:
#more disk0:snmp/ifindex-table loc 0/rsp0/cpu0
#more disk0:snmp/ifindex-table loc 0/rsp1/cpu0
#more disk0:snmp/snmp_persist loc 0/rsp0/cpu0
#more disk0:snmp/snmp_persist loc 0/rsp1/cpu0
Step 9
Perform redundancy switchover from active RSP to standby RSP5. This results in RSP5 (slot 1) becoming
active RSP and RSP (slot 0) becoming standby RP.
Example:
Router# redundancy switchover
Step 10
Verify that both the RSPs are in IOS XR RUN state using the show platform command
Example:
Router# show platform
Node
--------------------------------------------------------------------------------------
0/RSP0/CPU0
0/RSP1/CPU0
0/FT0
0/FT1
0/1/CPU0
0/FC0
0/FC1
0/FC2
0/FC3
0/FC4
0/PT0
0/PT1
A9K-RSP880-LT-TR(Active)
A9K-RSP5-TR(Standby)
ASR-9910-FAN
ASR-9910-FAN
A9K-8X100GE-TR
A99-SFC-S
A99-SFC-S
A99-SFC-S
A99-SFC-S
A99-SFC-S
A9K-AC-PEM-V3
A9K-AC-PEM-V3
The EEM scripts are files located on RSP's hard disk. These files are not automatically synced
between Active and Standby RSPs.
Type
A9K-RSP880-LT-TR(Standby)
A9K-RSP5-TR(Active)
ASR-9910-FAN
ASR-9910-FAN
A9K-8X100GE-TR
A99-SFC-S
A99-SFC-S
A99-SFC-S
A99-SFC-S
A99-SFC-S
A9K-AC-PEM-V3
A9K-AC-PEM-V3
Migrating from RSP4/RSP4-S/RSP-L to RSP5 Card
IOS XR RUN
NSHUT
IOS XR RUN
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
IOS XR RUN
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
State
Config state
IOS XR RUN
NSHUT
IOS XR RUN
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
IOS XR RUN
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
Replacing Cisco ASR 9000 Series Router Components
39