Digitrax DN163I2 Hızlı Başlangıç Kılavuzu - Sayfa 4
Medya Dönüştürücü Digitrax DN163I2 için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Digitrax DN163I2 8 sayfaları. Mobile decoder. n scale. 1.5 amp/2.0 amp peak 6 fx3 functions, 0.5 amp
Sayfayı Yazdır
Set Manual for complete programming instructions. Following is a brief
description of how to change the decoder address with a DT series throttles.
1. Place the loco on the programming track. Go into Program Mode on your
system. On DT400 press PROG. On DT300, DT100 & DT200 press
RUN/STOP & FN/F0 SIMULTANEOUSLY.
2. Choose AD2 for 2 digit addressing or AD4 for 4 digit addressing (DT300 &
DT400). (Ad for DT100 & DT200, see set manual for 4 digit instructions).
3. Choose the address you want to set up for the decoder.
4. Complete address programming. On DT400 press ENTER. On DT300,
DT100 & DT200 press SEL.
Note: CV29 must also be programmed to enable 4 digit addressing, this is
done automatically by the pressing the 'Y' key when prompted to do so on the
DT300 & DT400 throttles.
D D i i g g i i t t r r a a x x L L o o c c o o M M o o t t i i o o n n
Your locomotives look like the real thing, now you can make them run like the
real thing, too. Digitrax decoders incorporate torque compensation for smooth
as silk operation. You can also program CVs that control momentum, 3 step
and 128 step speed tables, switching speed, normal direction of travel,
scaleable speed stabilization and more to take full advantage of the Digitrax
LocoMotion System.
M M o o m m e e n n t t u u m m - - C C V V 0 0 3 3 & & C C V V 0 0 4 4
Acceleration is controlled by CV03 and deceleration by CV04. Both come
from the factory set to 000/x00. A range of 000/x00/ to 031/x1F is available for
both accel and decel. We recommend that you try CV03:003/x03 and
CV04:000/x00 as a starting point for experimenting with momentum.
S S p p e e e e d d T T a a b b l l e e s s - - H H o o w w t t h h e e L L o o c c o o R R e e s s p p o o n n d d s s t t o o t t h h e e T T h h r r o o t t t t l l e e
With Digitrax LocoMotion, there are two types of speed tables: 3 Step Tables
and High Resolution 28 Step Tables. Please see your Decoder Manual for a dis-
cussion of the 28 Step Tables. The 3 Step Tables are set up by programming 3
CVs: Start Voltage (CV02), Mid point Voltage (CV06) and Max Voltage
(CV05). These values are set at 000/x00 at the factory. All have a range of val-
ues from 000/x00 to 255/xFF. We recommend the following CV values as a
starting point for experimenting with speed tables.
©2008 Digitrax, Inc
D D
C C
i i g g i i t t r r a a x x
o o m m m m a a n n d d
R R u u n n Y Y o o u u r r T T r r a a i i n n s s , , N N o o t t Y Y o o u u r r T T r r a a c c k k ! !
S S y y s s t t e e m m
®
www.digitrax.com
C C
o o n n t t r r o o l l
4