Digitrax DN163PS Manuel - Sayfa 6

Medya Dönüştürücü Digitrax DN163PS için çevrimiçi göz atın veya pdf Manuel indirin. Digitrax DN163PS 8 sayfaları. Mobile decoder dcc plug'n play with 2.0” harness 1.5 amp/2 amp peak 6 fx3 functions, 0.5 amp

Sayfayı Yazdır

O O t t h h e e r r L L o o c c o o M M o o t t i i o o n n

T T r r a a v v e e l l & & S S c c a a l l e e a a b b l l e e S S p p e e e e d d S S t t a a b b i i l l i i z z a a t t i i o o n n ( ( B B a a c c k k E E M M F F ) ) F F e e a a t t u u r r e e s s

Switching speed is controlled by CV54. The factory setting is 000/x00 for

OFF. To turn on the switching speed feature, program CV54 to a value of

001/x01. When this feature is on, use F6 to activate and deactivate switching

speed. With the feature ON the throttle's target speed is

effectively reduced by approximately 50% and the effects of accel and decel

programmed into the decoder are reduced by 1/4. This is useful for yard

switching operations.

Normal Direction of Travel is controlled by CV29. See your decoder manual

for additional information on the settings for CV29.

Scaleable Speed Stabilization (Back EMF) intensity, or droop, is controlled

by CV57. The factory setting for this feature is 006/x06 which is suitable for

most locos. You can adjust this value in the range of 000/x00 for OFF to

015/x0F for the maximum effect. Consult your Digitrax Decoder Manual for

info about CVs 55 & 56 and their effects on scaleable speed stabilization. The

factory setting for both CV55 & CV56 is 000/x00.

S S u u p p e e r r S S o o n n i i c c S S i i l l e e n n t t O O p p e e r r a a t t i i o o n n a a n n d d T T o o r r q q u u e e C C o o m m p p e e n n s s a a t t i i o o n n

The factory settings in the decoder provide silent, smooth operation of your

locomotive under most conditions. For more information about these settings,

please see the Digitrax Decoder Manual or our website.

D D i i g g i i t t r r a a x x T T r r a a n n s s p p o o n n d d i i n n g g C C V V 6 6 1 1

Digitrax Transponding is controlled by CV61. The initial factory set value is

000/x00 for OFF. To turn on transponding, program CV61 to a value of

002/x02. This allows you to use Digitrax transponding to keep track of your

rolling stock. When transponding is enabled, the front light of the locomotive

will flicker slightly to indicate transponding signal is being communicated. For

optimal transponding operation, we recommend that you hook up the forward

and rear lights as shown above.

D D e e c c o o d d e e r r R R e e s s e e t t C C V V 0 0 8 8

Decoder reset lets you reset all CV values to the initial factory settings. To

reset all CV values, program CV08 to a value of 008/x08. You also have the

option of resetting all values except the 28 speed step tables. To do this,

program CV08 to a value of 009/x09.

D D

C C

i i g g i i t t r r a a x x

o o m m m m a a n n d d

R R u u n n Y Y o o u u r r T T r r a a i i n n s s , , N N o o t t Y Y o o u u r r T T r r a a c c k k ! !

F F e e a a t t u u r r e e s s : : S S w w i i t t c c h h i i n n g g S S p p e e e e d d , , N N o o r r m m a a l l D D i i r r e e c c t t i i o o n n o o f f

www.digitrax.com

C C

o o n n t t r r o o l l