argon audio BASS 12 Kullanıcı El Kitabı - Sayfa 2

Subwoofer argon audio BASS 12 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. argon audio BASS 12 5 sayfaları.

Sayfayı Yazdır

Subwoofer installation

The Subwoofer requires connection to the

mains power supply, so for your safety it is

important that you read both this manual and

the amplifier manual before connecting.

Subwoofer positioning

Variations in placement of loudspeakers can

produce dramatic differences in the way music

sounds. No listening room is the same and

therefore we encourage you to spend some

time experimenting with which placements

work best in your listening room. Positioning

of Subwoofers is however less critical

compared with full-range loudspeakers

because the low frequencies reproduced by a

subwoofer can be difficult to locate in the

room. You can start with our basic

recommendations.

To begin with, if you use the Subwoofer in a

surround set-up, the Subwoofer should ideally

be positioned between the TV and one of your

front loudspeakers, as fig. 2 to 4 on page 5. If

you are using the Subwoofer in a stereo set-

up the Subwoofer should ideally be positioned

between the two front stereo speakers, as

fig.1on page 5.

You should know that, if the Subwoofer is

placed close to a wall or in a corner, the bass

sound will be enhanced.

It's your choice what you like the most.

Another example is the placement of the

Subwoofer in the middle of the stereo

speakers or away from the center of the

stereo speakers.

This may have an impact on how you perceive

the stereo image, even though its only low

frequency sounds that come from the

Subwoofer.

Trust your ears and be willing to experiment

freely.

(Almost) everything is possible 

Running-in period

We recommend a running-in time of your new

BASS 12/15 Subwoofer of approximately 15-

20 hours at normal listening

level before you decide on the final positioning

and control settings of the Subwoofer. During

the running-in time the drive units will settle in

and perform as intended.

w w w . a r g o n a u d i o . c o m

B A S S 1 2 & 1 5

Connecting your Subwoofer

We recommend that you read the manual of

your Amplifier or AV-receiver carefully before

connecting your Subwoofer.

First switch off the Amplifier and all equipment

before you connect the Subwoofer.

Connect your Amplifier/av-reciever's

SUB-OUT or PRE-OUT to either INPUT

right/left (1 or 2) as shown on page 4.

If you use a Stereo Amplifier it's

recommended to use the INPUT right/left

connections (1) as shown on page 4.

If you use a AV receiver with a SUB out it's

recommended to use the LFE connection (2)

on page 4.

When finished, connect the subwoofer power

cable (9) as shown on page 4 to the mains

voltage, and push the POWER ON/OFF

button (10) as shown on page 4 to ON

position, the indicator lamp POWER LED will

now glow blue and the Subwoofer is active

and ready to be used.

The Argon BASS 12/15 Subwoofer has a

built-in AUTO STANDBY function ( 9) as

shown on page 4 and after approximately 20

minutes, without any input signal, the

subwoofer will automatically switch off, and

the indicator lamp POWER LED will change

color. When an input signal is detected the

subwoofer will become active and the

indicator lamp POWER LED will glow blue.

Setting volume, frequency and phase

The volume, crossover and phase (controls 4,

5 and 7) as shown on page 4, can be adjusted

on the rear panel, and we recommend that

you adjust the setting of these controls to your

liking – try with different music and films.