Cisco ASR 9000 Series Manuel - Sayfa 40
Ağ Geçidi Cisco ASR 9000 Series için çevrimiçi göz atın veya pdf Manuel indirin. Cisco ASR 9000 Series 44 sayfaları. Line card
Ayrıca Cisco ASR 9000 Series için: Ağ Ayarlarını Yapılandırma (26 sayfalar), Yapılandırma Kılavuzu (46 sayfalar), Yapılandırma Kılavuzu (50 sayfalar), Manuel (24 sayfalar), Yapılandırma (46 sayfalar), Hızlı Referans Kılavuzu (7 sayfalar)
Sayfayı Yazdır
- 1. Field Replaceable Units
- 2. Online Insertion and Removal
- 3. Powering off the Router
- 4. Replacing the Chassis Air Filter
- 5. Required Tools and Equipment
- 6. Removing a Fan Tray
- 7. Installing a Fan Tray
- 8. Disconnecting AC Power
- 9. Reconnecting AC Power
- 10. Disconnecting DC Power
- 11. Reconnecting DC Power
Migrating from RSP4/RSP4-S/RSP-L to RSP5 Card
Step 11
Verify RSP5 in slot 1 and RSP in slot 0 reach full synchronization (NSR-ready state) and status of ALL the
groups is Ready state. Use show redundancy command to verify the same.
Example:
Router# show redundancy
Fri Jul 12 20:51:19.365 UTC
Active Node
-----------
0/RSP1/CPU0
Step 12
Remove standby RSP (slot 0). Follow the procedure explained in the topic
from the Chassis, on page
Step 13
Insert and boot RSP5 (slot 0). After booting, the RSP5 becomes standby RSP.
Example:
Router# show platform
Node
--------------------------------------------------------------------------------
0/RSP0/CPU0
0/RSP1/CPU0
0/FT0
0/FT1
0/1/CPU0
0/FC0
0/FC1
0/FC2
0/FC3
0/FC4
0/PT0
0/PT1
Step 14
Repeat Step 6, Step 7 and Step 8.
Step 15
(Optional) Perform FPD upgrade on the RSP5. Use these commands:
Note
Example:
sysadmin-vm:0_RSP1# upgrade hw-module location 0/RSP0 fpd
sysadmin-vm:0_RSP1# upgrade hw-module location 0/RSP1 fpd
Step 16
Reload the system once FPDs are upgraded using the admin hw-module location all reload command.
Replacing Cisco ASR 9000 Series Router Components
40
Standby Node
------------
0/RSP0/CPU0(Node Ready, NSR:Ready)
25.
Type
A9K-RSP5-TR(Standby)
A9K-RSP5-TR(Active)
ASR-9910-FAN
ASR-9910-FAN
A9K-8X100GE-TR
A99-SFC-S
A99-SFC-S
A99-SFC-S
A99-SFC-S
A99-SFC-S
A9K-AC-PEM-V3
A9K-AC-PEM-V3
An FPD upgrade can be performed after all the FCs/LCs are added to the system.
Replacing Cisco ASR 9000 Series Router Components
Removing and Replacing Cards
State
Config state
IOS XR RUN
NSHUT
IOS XR RUN
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
IOS XR RUN
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT
OPERATIONAL
NSHUT