Acuity Brands 00194995254200 Hızlı Başlangıç Kılavuzu - Sayfa 5

Dış Mekan Işığı Acuity Brands 00194995254200 için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Acuity Brands 00194995254200 10 sayfaları.

Sayfayı Yazdır

READ AND FOLLOW THESE SAFETY INSTRUCTIONS!

• To reduce the risk of death, personal injury or property damage from fire,

electric shock, falling parts, cuts/abrasions, and other hazards please

read all warnings and instructions included with and on the fixture box

and all fixture labels.

• Before installing, servicing, or performing routine maintenance upon this

equipment, follow these general precautions.

• Commercial installation, service and maintenance of luminaires should

be performed by a qualified licensed electrician.

• For Residential installation: If you are unsure about the installation or

maintenance of the luminaires, consult a qualified licensed electrician

and check your local electical code.

• Maintenance of the luminaires should be performed by person(s)

familiar with the luminaires' construction and operation and any hazards

involved. Regular fixture maintenance programs are recommended.

• This fixture is intended to be connected to a properly installed and

grounded UL listed junction box.

• It will occasionally be necessary to clean the outside of the refractor/

lens. Refractor/lens should be washed in a solution of warm water and

any mild, non-abrasive household detergent, rinsed with clean water and

wiped dry. Should optical assembly become dirty on the inside, wipe

refractor/lens and clean in above manner, replacing damaged gaskets

as necessary.

• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been

properly packed so that no parts should have been damaged during

transit. Inspect to confirm. Any part damaged or broken during or after

assembly should be replaced.

• Recycle: For information on how to recycle LED electronic products,

please visit www.epa.gov.

• These instructions do not purport to cover all details or variations

in equipment nor to provide every possible contingency to meet in

connection with installation, operation, or maintenance. Should further

information be desired or should particular problems arise which are not

covered sufficiently for the purchaser's or owner's purposes, this matter

should be referred to Acuity Brands Lighting, Inc.

WARNING

RISK OF ELECTRIC SHOCK

► Disconnect or turn off power before installation or servicing.

► Verify that supply voltage is correct by comparing it with the luminaire

label information.

► Make all electrical and grounded connections in accordance with

the National Electrical Code (NEC) and any applicable local code

requirements.

► All wiring connections should be capped with UL approved wire

connectors.

CAUTION

RISK OF INJURY

► Wear gloves and safety glasses at all times when removing luminaire

from carton, installing, servicing or performing maintenance.

► Avoid direct eye exposure to the light source while it is on.

WARNING

RISK OF BURN

► Allow lamp/fixture to cool before handling. Do not touch enclosure, lens

or light source.

► Do not exceed maximum wattage marked on luminaire label.

► Follow all manufacturer's warnings, recommendations and restrictions

including but not limited to: driver type, burning position, mounting

locations/methods, replacement and recycling.

► Use only lamps that comply with ANSI standards.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

RISK OF FIRE

► Keep combustible and other materials that can burn, away from lamp/

lens.

► Do not operate in close proximity to persons, combustible materials or

substances affected by heat.

CAUTION

RISK OF PRODUCT DAMAGE

► Never connect components under load.

► Do not mount or support these fixtures in a manner that can cut the outer

jacket or damage wire insulation.

► Unless individual product specifications deem otherwise: Never connect

an LED product directly to a dimmer packs, occupancy sensor, timing

device, or other related control devices. LED fixtures must be powered

directly off a switched circuit.

► Unless individual product specifications deem otherwise: Do not restrict

fixture ventilation. Allow for some volume of airspace around the fixture.

Avoid covering LED fixtures with insulation, foam, or other material that

will prevent convection or cooling.

► Unless individual product specifications deem otherwise: Do not exceed

fixtures maximum ambient temperature.

► Only use fixture in its intended location.

► LED products are Polarity Sensitive. Ensure proper Polarity before

installation.

► Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal

grounding equipment must be worn during all installation or servicing

of unit.

► Do not touch individual electrical components as this can cause ESD,

shorten lamp life, or alter performance.

► Some components inside the fixture may not be serviceable. In the

unlikely event your unit may require service, stop using the unit

immediately and contact an ABL representative for assistance.

► Changes or modifications not expressly approved by Acuity Brands

Lighting could void the authority to operate the equipment.

► Always read the fixtures complete installation instructions prior to

installation for any additional fixture specific warnings.

This equipment has been tested and found to comply with the limits for a

class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

when used in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions may cause harmful interference to radio

communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

5-YEAR LIMITED WARRANTY

product registration confirms your right to the protection available under

the terms and conditions of your Lithonia Lighting warranty.

Failure to follow any of these instructions could void product warranties.

For a complete listing of product Terms and Conditions, please visit www.

acuitybrands.com. Acuity Brands Lighting, Inc. assumes no responsibilities

for claims arising out of improper or careless installation or handling of its

products.

page 2