Acuity Brands 00194995255139 Hızlı Başlangıç Kılavuzu - Sayfa 6

Dış Mekan Işığı Acuity Brands 00194995255139 için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Acuity Brands 00194995255139 10 sayfaları.

Sayfayı Yazdır

1. PREPARE FOR INSTALLATION

Remove fixture components and parts pack. Check to ensure

all parts are included. Note: Account for small parts and destroy

packing material, as these may be hazardous to children.

FIXTURE PACKING LIST

Part Description

A Light Fixture.......................................................................... 1

Lamp Head........................................................................... 2

C Accent Light / Motion sensor ................................................ 1

D Mounting bracket (pre-installed) .......................................... 1

E 2" #8 Center Mounting Screw (pre-installed) ....................... 1

F 3/4" #8 & #6 & #10 Mounting Screws* ................................ 6

G Wire Nuts* ............................................................................ 3

H Rubber Plug*........................................................................ 1

*Contained in parts packs

Mounting Hardware Included

Silicone Sealant Required

REQUIRED TOOLS

2. SELECT MOUNTING LOCATION

For installation to properly installed and grounded UL listed round

recessed or surface mounted weatherproof junction box.

Suitable for wall mount

between 6 to 8ft (1,8-2,4m) height with

Accent light facing the ground. Not suitable for mounting within

(1.2m) from ground

Note: Mounting fixture above or below the recommended height

may cause motion sensor not to work properly. If fixture is mounted

higher than 8ft (2.4m), the distance and downward sensitivity

will be reduced. The detector is less sensitive to motion directly

towards it.

Do NOT use with dimmers or timers or on multiple switch circuits.

Do NOT install on the same circuit with an electric motor (i.e.

appliances, HVAC equipment, washer/dryer, garage door

openers, etc.

Do NOT install near objects that change temperature rapidly, such

as heating vents and air conditioners. These heat sources

could cause false triggering.

Do NOT install Nearby large, light-colored objects reflecting light

may trigger the shut-off feature. Do not point other lights at the

daylight sensor.

3. INSTALLING MOUNTING BRACKET

Turn OFF Power at circuit breaker box

CAUTION: Do not rely on wall switch alone to turn off power.

Note: Center mounting screw and bracket are pre-installed on the

light fixture for shipping.

•

Loosen the center mounting screw (E) and remove the

mounting bracket.

•

Install the mounting bracket (D) to the junction box using two

3/4" #6 or #8 or #10 mounting screws (F).

Note: Choose one of the 3 screw sizes provided depending on

your junction box.

INSTALLATION INSTRUCTIONS

Quantity

4. CAUTION: WIRING

4ft

Make sure power is turned off.

•

Use wire nut to connect the bare copper or green house

supply ground wire to the green fixture ground wire. Note:

If house wiring does not include a ground wire, consult your

local electrical code for approved grounding methods.

For proper connection, place wire nut over wires

•

Use wire nut to connect the white fixture wire to the white

(neutral) house supply wire.

•

Use wire nut to connect the black fixture wire to the black

house supply wire.

5. MOISTURE SEAL

•

Apply silicone caulking (not included) around perimeter of the

fixture where it contacts the mounting surface to avoid water

entry.

6. FIXTURE INSTALLATION

•

Align fixture over j-box and secure to mounting bracket by

tightening center mounting screw (E).

Note: Make sure no wires are pinched before tightening.

•

Insert rubber plug (H) into center hole to cover the center

mounting screw head for moisture seal.

Turn on electricity at fuse or circuit breaker box and make sure the

wall switch is on.

Note: Light will not come on during daylight.

•

Cover Light Sensor to verify success of installation.

page 3

and twist clockwise until tight.

REV. DESCRIPTION

CONFIDENTIAL:

NLightend Proprie

UNLESS OTHERWISE SPECIFIED

NLigh

ALL DIMENSIONS ARE IN MILLIMETERS

100MM OR MORE ± 0.5

0 TO 99MM

0.10

ANGULAR TOL

1/2 ° .

DO NOT SCALE DRAWING

SHT I

DRAWN BY: DRS