Cisco Linksys WAG310G Kullanıcı Kılavuzu - Sayfa 17
Ağ Geçidi Cisco Linksys WAG310G için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Cisco Linksys WAG310G 39 sayfaları. Wireless-g adsl2+ iad gateway
Sayfayı Yazdır
Chapter3
sends the next DTIM with a DTIM Interval value. Its clients
hear the beacons and awaken to receive the broadcast
and multicast messages. The default value is 1.
Fragmentaton Threshold
maximum size for a packet before data is fragmented
into multiple packets. If you experience a high packet
error rate, you may slightly increase the Fragmentation
Threshold. Setting the Fragmentation Threshold too low
may result in poor network performance. Only minor
reduction of the default value is recommended. In most
cases, it should remain at its default value of 23.
RTS Threshold
Should you encounter inconsistent
data flow, only minor reduction of the default, 23, is
recommended. If a network packet is smaller than the
preset RTS threshold size, the RTS/CTS mechanism will
not be enabled. The Gateway sends Request to Send (RTS)
frames to a particular receiving station and negotiates
the sending of a data frame. After receiving an RTS, the
wireless station responds with a Clear to Send (CTS) frame
to acknowledge the right to begin transmission. The RTS
Threshold value should remain at its default value of
23.
Click Save Settngs to apply your changes, or click Cancel
Changes to cancel your changes.
Security > Firewall
The Firewall screen is used to configure a firewall that
can filter out various types of unwanted traffic on the
Gateway's local network.
Security > Firewall
Firewall
SPI Frewall Protecton
To use firewall protection,
keep the default selection, Enable. To turn off firewall
protection, select Dsable.
Additional Filters
Flter Proxy
Use of WAN proxy servers may compromise
the Gateway's security. Denying Proxy will disable access
to any WAN proxy servers. Select Flter Proxy to enable
proxy filtering. Deselect the feature to allow proxy access.
Wreless-G ADSL2+ IAD Gateway
This value specifies the
Advanced Configuration
Flter Java Applets
Java is a programming language for
websites. If you deny Java, you run the risk of not having
access to Internet sites created using this programming
language. Select Flter Java Applets to enable Java
filtering. Deselect the feature to allow Java usage.
Flter Cookes
A cookie is data stored on your computer
and used by Internet sites when you interact with them.
Select Flter Cookes to filter cookies. Deselect the feature
to allow cookie usage.
Flter ActveX
ActiveX is a programming language for
websites. If you deny ActiveX, you run the risk of not having
access to Internet sites created using this programming
language. Select Flter ActveX to enable ActiveX filtering.
Deselect the feature to allow ActiveX usage.
Block WAN Requests
Block Anonymous Internet Requests
makes it more difficult for outside users to work their
way into your network. This feature is selected by default.
Deselect the feature to allow anonymous Internet
requests.
Click Save Settngs to apply your changes, or click Cancel
Changes to cancel your changes.
Security > VPN Passthrough
The VPN Passthrough screen allows you to enable VPN
tunnels using IPSec, PPTP, or L2TP protocols to pass through
the Gateway's firewall.
Security > VPN Passthrough
VPN Passthrough
IPSec Passthrough
Internet Protocol Security (IPSec) is
a suite of protocols used to implement secure exchange
of packets at the IP layer. To allow IPSec tunnels to pass
through the Gateway, keep the default, Enable.
PPTP Passthrough
Point-to-Point Tunneling Protocol
(PPTP) allows the Point-to-Point Protocol (PPP) to be
tunneled through an IP network. To allow PPTP tunnels to
pass through the Gateway, keep the default, Enable.
This feature
1