Epson FX-880+ Manuel - Sayfa 11

Yazıcı Aksesuarları Epson FX-880+ için çevrimiçi göz atın veya pdf Manuel indirin. Epson FX-880+ 18 sayfaları. Epson serial impact dot matrix printers
Ayrıca Epson FX-880+ için: Kurulum Kılavuzu (33 sayfalar), Broşür ve Teknik Özellikler (24 sayfalar), Teknik Özellikler (2 sayfalar), Önce Bunu Okuyun (2 sayfalar), Referans Kılavuzu (34 sayfalar), Hızlı Kılavuz (33 sayfalar)

Sayfayı Yazdır

2. Hold down the

Pause

Pause light begins flashing and the printer enters Micro

Adjust mode.

D to feed paper backward, or

3. Press

LF/FF

feed paper forward, until the paper perforation is aligned

with the tear-off edge of the printer cover.

The printer has a minimum and a maximum tear-off

position. If you try to adjust the tear-off position beyond

these limits, the printer beeps and stops moving the

paper.

4. Tear off the printed pages.

5. Press the

button to turn off Micro Adjust mode.

Pause

When you resume printing, the printer automatically feeds the

paper back to the top-of-form position and begins printing.

Adjusting the top-of-form position

The top-of-form position is the position on the page where the

printer starts printing. If your printing appears too high or low

on the page, you can use the Micro Adjust function to adjust

the top-of-form position, as described below. Your top-of-form

position setting remains in effect until you change it, even if you

turn off the printer.

Never use the knob to adjust the top-of-form position;

this may damage the printer or cause it to lose the

top-of-form position.

1. Make sure the printer is turned on.

2. Load paper. (If the tractor is in a push position, press the

button to advance continuous paper to the

Load/Eject

current top-of-form position.) If necessary, lift up the

printer cover so you can see the paper position.

3. Hold down the

Pause

light flashes and the printer enters Micro Adjust mode.

button for about three seconds. The

Load/Eject

tear-off edge

paper

perforation

button for three seconds. The Pause

4. Press the

LF/FF

up on the page, or press the

the top-of-form position down on the page.

U to

5. Press the

Pause

The printer has a minimum and a maximum top-of-form

position. If you try to adjust it beyond these limits, the

printer beeps and stops moving the paper.

When the paper reaches the default top-of-form

position, the printer beeps and stops moving the paper

briefly. You can use this setting as a reference point

when adjusting the position.

The top margin setting made in some software

overrides the top-of-form position setting you make

with the Micro Adjust function.

Loading Special Papers

Follow the guidelines in this section when loading continuous

multipart forms, single-sheet multipart forms, labels, and

envelopes.

Continuous multipart forms

Except for setting the paper-thickness lever, you load

continuous multipart forms the same way as ordinary

continuous paper. Just keep the following in mind:

Be sure your multipart forms do not exceed 0.018 inch

(0.46 mm) in thickness.

Do not load paper that is curled or has been folded.

Thick paper, such as multipart forms with five or six parts,

requires a straight paper path to avoid paper jams. Load

thick paper in the front or bottom slots.

10/01

EPSON FX-880+/FX-1180+

D button to move the top-of-form position

U button to move

Load/Eject

button to exit Micro Adjust mode.

EPSON FX-880+/FX-1180+