Motorola C1001LX Manuel - Sayfa 2
Telsiz Telefon Motorola C1001LX için çevrimiçi göz atın veya pdf Manuel indirin. Motorola C1001LX 2 sayfaları. C100 series
Ayrıca Motorola C1001LX için: Manuel (2 sayfalar)
Sayfayı Yazdır
6. Services
5.1.5
Battery tones
When you the battery is running low you will hear a warning beep. You
6.1
Call List type
can switch this beep on or off.
m
You can set the Call list to show All calls or Missed calls only. If All calls
d
1.
Press
, scroll
to
Phone setup.
m
is selected, press
2.
Press
. The display shows
.
Sounds
calls is selected, press
m
m
d
3.
Press
. Scroll
to
Battery tone
.
1.
Press
m
m
u
d
4.
Press
,
or
to select
or
and press
to confirm.
On
Off
2.
The display shows
5.2
Handset name
3.
Scroll
u
confirm.
Personalize your handset, with a name or location for example Peter or
Bedroom. Maximum 12 characters.
6.2
Area code
m
d
1.
Press
, scroll
to
Phone setup.
You can set your local area code into the phone. When a number from
m
2.
Press
. The display shows
.
that area code calls only the local number will be displayed and stored.
Sounds
m
The area code can be up to 3 digits long.
3.
Scroll
d
to
and press
.
Phone name
m
b
Note: If the area code is stored in the phone it will not display the full
4.
Enter the new handset name and press
to confirm.
phone number.
m
Delete the current name by pressing
.
1.
Press
5.3
Date & time
m
d
2.
Scroll
d
1.
Press
, scroll
to
Phone setup.
m
3.
Using the keypad enter the area code and press
2.
Press
. The display shows
.
Sounds
m
6.3
Flash time
3.
Scroll
d
to
and press
.
Date & time
Depending on your country and network operator, your C100xLX has
4.
Enter the date using the keypad (e.g. 08--12--14 for 12th of August
m
the flash time set as 600 ms (Long). It is unlikely that you need to change
2014) and press
to confirm.
this setting unless advised to do so.
m
5.
Enter the time using the 12 hour format
, e.g. 02:45 for 2:45.
hh:mm
m
1.
Press
u
d
6.
Scroll
or
to select
or
and press
to confirm.
am
pm
2.
Scroll
d
5.4
Language
u
m
3.
Press
1.
Press
, scroll
d
to
confirm.
Phone setup.
m
2.
Press
. The display shows
Sounds
.
m
d
3.
Scroll
to
and press
.
Language
m
4.
Scroll
u
or
d
to select the required language and press
to
confirm.
7.2.4
Delete an entry
No ring tone
d
•
The ring tone is deactivated.
1.
Press
to open the Calls list.
•
Increase the volume.
u
d
2.
Scroll
or
to the entry you want.
m
Caller ID service does not work
3.
Press
, the display shows
.
View
m
b
•
Check your subscription with your network operator.
4.
Scroll
d
to
and press
. The display shows
.
Delete
Confirm?
m
A phonebook entry cannot be stored
5.
Press
to confirm or
to cancel.
•
The phonebook is full. Delete an entry to free memory.
7.2.5
Delete the entire Calls list
d
No display
1.
Press
to open the Calls list.
m
•
Try recharging or replacing the batteries.
2.
Press
, the display shows
.
View
m
b
•
Try disconnecting and connecting the base power supply.
3.
Scroll
d
to
and press
. The display shows
.
Delete all
Confirm?
m
•
If the LED is not lit up, then try disconnecting and connecting the
4.
Press
to confirm or
to cancel.
base power supply.
8. Help
Unable to register another handset
•
Maximum number of 4 handsets has been reached.
The
icon is not scrolling during charge
•
The display shows
•
Bad battery contact – move the handset slightly.
to register a new one.
•
Dirty contact – Clean the battery contact with a cloth moistened
Noise interference on your radio or television
with alcohol.
•
Your base or charger may be too close. Move it as far away as
•
Battery is full – no need to charge.
possible.
No dialling tone
•
No power – check the connections. Reset the phone: unplug and
plug back in the electrical outlet.
•
Batteries are empty – charge the batteries for at least 24 hours.
•
You are too far from the base – move closer to the base.
•
Wrong line cable – use the line cable provided.
Poor audio quality
•
The base is too close to electrical appliances, reinforced concrete
walls or metal doorframes – move the base at least 3 feet away away
from any electrical appliances.
The
icon is blinking or has disappeared
•
Handset is not registered to the base – register the handset to the base.
•
You are too far from the base – move closer to the base.
than MOTOROLA, BINATONE or its authorized service centers, are
Products Covered
Length of Coverage
excluded from coverage.
Consumer Products
One (1) year from the date of the products
Altered Products. Products or Accessories with (a) serial numbers or
original purchase by the first consumer
date tags that have been removed, altered or obliterated; (b) broken
purchaser of the product.
seals or that show evidence of
Consumer Accessories
Ninety (90) days from the date of the
tampering; (c) mismatched board serial numbers; or (d) nonconforming
or non-Motorola branded housings, or parts, are excluded from
accessories original purchase by the first
consumer purchaser of the product.
coverage.
Consumer Products and
The balance of the original warranty
Communication Services. Defects, damages, or the failure of Products
or Accessories due to any communication service or signal you may
or for ninety (90) days from the date
Accessories that are
subscribe to or use with the Products or Accessories is excluded from
returned to the consumer, whichever is
Repaired or Replaced
longer.
coverage.
How to Obtain Warranty Service or Other Information?
Exclusions
To obtain service or information, please call:
Normal Wear and Tear. Periodic maintenance, repair and replacement
US and Canada: 1-888-331-3383
of parts due to normal wear and tear are excluded from coverage.
Email: [email protected]
Batteries. Only batteries whose fully charged capacity falls below 80% of
You will receive instructions on how to ship the Products or Accessories
their rated capacity and batteries that leak are covered by this Warranty.
at your expense and risk, to a BINATONE Authorized Repair Center.
To obtain service, you must include: (a) the Product or Accessory; (b)
Abuse & Misuse. Defects or damage that result from: (a) improper
the original proof of purchase (receipt) which includes the date, place
operation, storage, misuse or abuse, accident or neglect, such as
and seller of the Product; (c) if a warranty card was included in your box,
physical damage (cracks, scratches, etc.)
a completed warranty card showing the serial number of the Product;
to the surface of the product resulting from misuse; (b) contact with
(d) a written description of the problem; and, most importantly; (e) your
liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or
address and telephone number.
the like, extreme heat, or food; (c)
use of the Products or Accessories for commercial purposes or
These terms and conditions constitute the complete warranty
subjecting the Product or Accessory to abnormal usage or conditions; or
agreement between you and BINATONE. regarding the Products or
(d) other acts which are not the fault of MOTOROLA or BINATONE., are
Accessories purchased by you, and supersede any prior agreement
excluded from coverage.
or representations, including representations made in any literature
publications or promotional materials issued by BINATONE. or
Use of Non-Motorola branded Products and Accessories. Defects or
representations made by any agent employee or staff of BINATONE, that
damage that result from the use of Non-Motorola branded or certified
may have been made in connection with the said purchase.
Products or Accessories or other peripheral equipment are excluded
from coverage. Unauthorized Service or Modification. Defects or
damages resulting from service, testing, adjustment, installation,
maintenance, alteration, or modification in any way by someone other
6.4
Dial mode
The default C100xLX dialling mode is suitable for your country and
network operator. It is unlikely that you should need to change this
setting unless advised to do so.
m
d
key in idle and you can view all calls lists. If Missed
d
1.
Press
, scroll
to
d
key in idle and you can view missed call only.
m
2.
Scroll
d
to
Dial mode
d
, scroll
to
and press
.
Services
m
3.
Press
u
or
d
to select
, press
.
Call list type
m
6.5
Switch Auto clock on / off
or
d
to select
or
and press
to
All calls
Missed calls
If you have subscribed to a Caller ID Service, the date and time will be
set on all your handsets whenever a call is received. This feature can be
set to On or Off.
m
1.
Press
, scroll to
Services
2.
Scroll
d
to
Auto clock
3.
Scroll
d
to
or
On
Off
6.6
Registration
m
, scroll
d
to
and press
.
Services
Up to 4 handsets can be registered to one base station. Additional
m
handsets must be registered to the base before you can use them.
to
Area code
is displayed. Press
.
m
•
The instructions described below apply specifically to your C100xLX
to confirm.
handset. If you wish to register another manufacturer's handset, the
instructions may vary. In this case, please refer to the manufacturer
of the additional handset.
•
The Master PIN is required before you can register or unregister
handsets. The PIN is 0000.
m
6.6.1
Register a handset
, scroll
d
to
and press
.
Services
m
At the base:
to
and press
.
p
Flash time
m
d
1.
Press and hold the
or
to select
,
or
and press
to
Short
Medium
Long
120 seconds in which to register a handset.
At the handset:
1.
If the handset is not already registered to a base, press
2.
Or if the handset is already registered to a base, press
m
to
and press
Services
9. General information
If your product is not working properly...
1.
Read this User's Guide.
2.
Visit our website: www.motorola.com
3.
Contact Customer Service in the US and Canada at
1-888-331-3383
Email: [email protected]
Important safety instructions
Follow these safety precautions when using your phone to reduce the
risk of fire, electric shock, and injury to persons or property:
1.
Keep all vents and openings of the phone unblocked.
Do not set the phone on a heating register or over a radiator. Ensure
that proper ventilation is provided at the installation site.
2.
Do not use while wet or while standing in water.
. You must unregister a handset in order
Searching
3.
Do not use this product near water (for example, near a bath tub,
kitchen sink, or swimming pool).
4.
Do not allow anything to rest on the power cord. Place the power
cord so that it will not be walked on.
5.
Never insert objects of any kind into the product vents as that may
result in fire or electric shock.
6.
Unplug this product from the electrical outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
7.
Do not disassemble this product. If service or repair work is required,
contact the customer service helpline found in this User's Guide.
8.
Do not overload wall outlets and extension cords.
9.
Avoid using during an electrical storm. Use a surge protector to
protect the equipment.
10. Do not use this phone to report a gas leak, especially if you are in the
vicinity of the gas line.
FCC, ACTA and IC regulations
FCC Part 15
This equipment has been tested and found to comply with the
requirements for a Class B digital device under Part 15 of the Federal
Communications Commission (FCC) rules. These requirements are
intended to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by
the party responsible for compliance could void the user's authority to
operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Privacy of
communications may not be ensured when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount
of radio frequency energy that can be safely absorbed by a user or
bystander according to the intended usage of the product. This product
has been tested and found to comply with the FCC criteria. Both the
Handset may be safely held against the ear of the user. The telephone
base shall be installed and used such that parts of the user's body other
than the hands are maintained at a distance of approximately 20 cm (8
inches) or more.
3.
When the display shows
, enter the base PIN and press
PIN
When the handset registers with the base, it is assigned a handset
number.
m
6.6.2
Un-register a handset
and press
.
Services
m
Use one handset to delete another. You cannot delete the handset that
and press
.
you are using.
m
m
or
and press
to confirm.
Tone
Pulse
1.
Press
, scroll
d
to
and press
Services
m
2.
Scroll
d
to
and press
Unregister
3.
Enter the 4 digit master PIN and press
Display shows the first registered handset number.
m
4.
Scroll
u
or
d
to select the handset you want to delete and press
m
and press
.
m
.
and press
.
is displayed on the handset screen.
m
Unregistered
then press
to confirm.
6.7
Restore default settings
You can restore your C100xLX to its default (original) settings.
All the handsets that are registered to the base will be retained.
IMPORTANT
Resetting your phone to its default setting will delete all entries in the
Phonebook and Calls list. All handset and base settings will also be reset.
m
1.
Press
, scroll
d
to
and press
Services
m
d
2.
Scroll
to
Reset
and press
.
m
3.
Confirm?
is displayed. Press
.
6.8
Default settings
Handset name
HANDSET Phonebook
on the base until the base beeps. You have
Low battery beeps
ON
Docking tone
ON
m
Key tone
ON
.
Ringer tones
1
m
d
scroll
Ringer volume
3
m
Earpiece volume
1
. Scroll
d
to
and press
.
Register
CAUTION
To reduce the risk of fire, use only No. 26 AWG or larger UL Listed or CSA
Certified Telecommunication Line Cord.
Unplug this cordless phone immediately from an
outlet if:
•
The power cord or plug is damaged or frayed.
•
Liquid has been spilled on the product.
•
The product has been exposed to rain or water. Do not retrieve
the handset or base until after you have unplugged the power and
phone from the wall. Then retrieve the unit by the unplugged cords.
•
The product has been dropped or the cabinet has been damaged.
•
The product exhibits a distinct change in performance.
Installation Guidelines
1.
Read all instructions and save them for future reference.
2.
Follow all warnings and instructions marked on the product.
3.
Do not install this product near a bath tub, sink, or shower.
4.
Operate this phone using only the power source that is indicated
on the marking label. If you are unsure of the power supply to your
home, consult with your dealer or local power company.
5. Do not place this product on an unstable cart, stand, or table. This
product may fall, causing serious damage to the product.
6.
Adjust only those controls that are covered by the operating
instructions. Improper adjustment of other controls may result in
damage and will often require extensive work to restore the product
to normal operation.
7.
Clean this product with a soft, damp cloth. Do not use chemicals or
cleaning agents to clean this phone.
8.
Use only the power supply that came with this unit. Using other
power supplies may damage the unit.
9.
Because this phone operates on electricity, you should have at least
one phone in your home that operates without electricity in case of
a power outage.
This Class B digital apparatus complies with Canadian ICES-003.
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation
of the device.
Le present appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation
est autorisee aux deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioelectrique subi, meme si le brouillage est susceptible
d'en compromettre le fonctionnement.
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with
technical requirements adopted by the Administrative Council for
Terminal Attachments (ACTA). This Product Complies With 47CFR
PART 68.
The plug and jack used to connect this equipment to premises wiring
and the telephone network must comply with applicable Part 68 rules
and technical requirements adopted by ACTA. A compliant telephone
cord and modular plug is provided with this product. It is designed to be
connected to a compatible modular jack that is also compliant. An RJ11
jack should normally be used for connecting to a single line and an RJ14
jack for two lines. See Installation Instructions in the User's Guide.
The Ringer Equivalence Number (REN) is used to determine how many
devices you may connect to your telephone line and still have them ring
when you are called. The REN for this product is encoded as the 6th and
7th characters following the US: in the product identifier (e.g., if ## is
03, the REN is 0.3). In most, but not all areas, the sum of all RENs should
be five (5.0) or less. For more information, please contact your local
telephone company.
This equipment may not be used with Party Lines. If you have specially
wired alarm dialing equipment connected to your telephone line, ensure
the connection of this equipment
does not disable your alarm equipment. If you have questions about
m
7. Caller ID and the Calls list
.
IMPORTANT
To use Caller ID, you must first subscribe to the service from your network
provider. A subscription fee may be applicable.
To ensure that the caller's name is displayed, make sure you have stored
the full telephone number, including the area code in the phonebook.
m
.
If the call is blocked,
Private
will be displayed.
If the number is unavailable,
will be displayed.
Unknown
.
If the call is from the operator,
will be displayed.
m
Operator
If the call is from a payphone,
will be displayed.
.
Payphone
If the call is from a ringback request,
will be displayed.
Ringback
7.1
Caller ID
If you have subscribed to a Caller ID Service, you will be able to see
your caller's number on your handset (provided it is not withheld)
prior to answering the call. The display can show the first 16 digits or 14
characters of the phone numbers.
If your caller's name and number are stored in the phonebook and a
number match is found, you will see the caller's name on the display as
well.
7.2
Calls list
m
The Calls list stores details of your last 50 received calls, including the
.
phone number, date and time of call.
The Calls list also alerts you when you have unanswered calls.
The caller's details are stored in the Calls list whether or not you have
answered the call. The list is shared by all handsets registered to the base.
When the list is full, and a new call is received, the oldest entry will be
deleted automatically.
Empty
Calls list
Empty
When you have missed call(s) (incoming calls that you haven't answered)
Redial list
Empty
the display will show
X Missed call(s)
m
and the
icon will flash on all handsets
registered to the base. Press
to see the callers details.
PIN code
0000
Dial mode
Tone
Flash mode
Long (600 ms)
Keypad lock
OFF
10. To avoid interference to nearby appliances, do not place the base of
the phone on or near a TV, microwave oven, or VCR.
CAUTION
To maintain compliance with the FCC's RF exposure guidelines, place
the base unit at least 8 inches from nearby persons.
Battery Safety Instructions
•
Do not burn, disassemble, mutilate, or puncture the battery. The
battery contains toxic materials that could be released, resulting in
injury.
Consumer Products and Accessories
Limited Warranty ("Warranty")
Thank you for purchasing this Motorola branded product manufactured
under license by Binatone Electronics International LTD ("BINATONE").
What Does this Warranty Cover?
Subject to the exclusions contained below, BINATONE warrants that
this Motorola branded product ("Product") or certified accessory
("Accessory") sold for use with this product that it manufactured to be
free from defects in materials and workmanship under normal consumer
usage for the period outlined below. This Warranty is your exclusive
warranty and is not transferable.
Who is covered?
This Warranty extends only to the first consumer purchaser, and is not
transferable.
what will disable alarm equipment, consult your telephone company or
a qualified installer.
If this equipment is malfunctioning, it must be unplugged from the
modular jack until the problem has been corrected. Repairs to this
telephone equipment can only be made by the manufacturer or its
authorized agents. For repair procedures, follow the instructions outlined
under the Limited Warranty.
If this equipment is causing harm to the telephone network, the
telephone company may temporarily discontinue your telephone
service. The telephone company is required to notify you before
interrupting service. If advance notice is not practical, you will be
notified as soon as possible. You will be given the opportunity to correct
the problem and the telephone company is required to inform you of
your right to file a complaint with the FCC. Your telephone company
may make changes in its facilities, equipment, operation, or procedures
that could affect the proper functioning of this product. The telephone
company is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is
hearing aid compatible.
If this product has memory dialing locations, you may choose to store
emergency telephone numbers (e.g., police, fire, medical) in these
locations. If you do store or test emergency numbers, please:
•
Remain on the line and briefly explain the reason for the call before
hanging up.
•
Perform such activities in off-peak hours, such as early morning or
late evening.
Industry Canada
Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any
interference, including interference
that may cause undesired operation.
The term "IC: " before the certification/registration number only signifies
that the Industry Canada technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment
is 0.0B. The REN is an indication of the maximum number of devices
7.2.1
View the Calls list
1.
Press
d
to open the Calls list. If there are no calls in the list, the
display shows
.
List empty
• The most recent number or name if stored in the phonebook
is displayed.
u
d
2.
Press
or
to scroll through the list.
• If the call was answered,
icon is displayed as you scroll to the
entry. If the call was unanswered,
icon is displayed as you
scroll to the entry.
b
• If the telephone number is longer than 16 digits, u icon is
displayed. Press
to see the remaining digits.
m
• Press
to access the option to store the entry in your
phonebook.
m
#
• Press
twice to see the time and date of the call.
3.
When viewing a calls list number press
to toggle the Calls List
between different formats, e.g. YYY-YYYY, AAA-YYY-YYYY or
1-AAA-YYY-YYYY.
7.2.2
Dial a number in the Calls list
d
1.
Press
to open the Calls list.
u
t
d
2.
Scroll
or
to the entry you want.
3.
Press
to dial the displayed entry.
7.2.3
Save a number from a Calls list number to the phonebook
1.
Press
d
to open the Calls list.
u
d
2.
Scroll
or
to the entry you want.
m
3.
Press
, the display shows
.
View
m
4.
Scroll
d
to
and press
.
Save number
5.
The display shows
.
Enter name
m
6.
Enter the name and press
. The number is displayed.
m
7.
Edit the number if necessary, then press
. The number is stored.
SAVE THESE INSTRUCTIONS
What will BINATONE do?
BINATONE or its authorized distributor at its option and within a
commercially reasonable time, will at no charge repair or replace any
Products or Accessories that does not
conform to this Warranty. We may use functionally equivalent
reconditioned/ refurbished/ pre-owned or new Products, Accessories
or parts.
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE
DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE REPAIR
OR REPLACEMENT PROVIDED UNDER THIS EXPRESS LIMITED
WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER, AND
IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OF
IMPLIED. IN NO EVENT SHALL MOTOROLA OR BINATONE BE LIABLE,
WHETHER IN CONTRACT OR TORT (INCLUDING
NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASE
PRICE OF THE PRODUCT OR ACCESSORY, OR FOR ANY INDIRECT,
INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF REVENUE
OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR
OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION
WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS OR
ACCESSORIES TO THE FULL EXTENT THESE DAMAGES MAY BE
DISCLAIMED BY LAW.
Some jurisdictions do not allow the limitation or exclusion of incidental
or consequential damages, or limitation on the length of an implied
warranty, so the above limitations or exclusions may not apply to you.
This Warranty gives you specific legal rights, and you may also have
other rights that vary from one jurisdiction to another.
allowed to be connected to a telephone interface. The termination on
an interface may consist of any combination of devices subject only to
the requirement that the sum of the RENs of all the devices does not
exceed five.
This equipment meets the applicable Industry Canada Terminal
Equipment & Technical Specifications.
Placing the receiver slightly above the ear may result in better
performance for hearing aids with microphones positioned behind the
ear.
Specific Absorption Rate (SAR) information
SAR tests are conducted using standard operating positions accepted
by the FCC with the phone transmitting at its highest certified power
level in all tested frequency bands, although the SAR is determined at
the highest certified power level, the actual SAR level of the phone while
operating can be well below the maximum value, in general, the closer
you are to a wireless base station antenna, the lower the power output.
Before a new model phone is a available for sale to the public, it must be
tested and certified to the FCC that it does not exceed the exposure
limit established by the FCC, Tests for each phone are performed
in positions and locations (e.g. at the ear) as required by the FCC.
This handset has also been tested and meets the FCC RF exposure
guidelines. Use of other accessories may Non-compliance with the
above restrictions may result in violation of RF exposure guidelines.