Motorola D1013 Kullanıcı Kılavuzu - Sayfa 23

Telsiz Telefon Motorola D1013 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Motorola D1013 30 sayfaları. Motorola d1010 series digital cordless phone with answer machine

Sayfayı Yazdır

Switch handset call screening on/off

m
u
d
1. Press
, scroll
or
to
ANSW MACHINE
d
m
2. Scroll
to
ANSW SETTINGS
and press
m
3. Scroll to
HS SCREENING
and press
.
u
d
4. Scroll
or
to select
ON
or OFF.
m
5. Press
to confirm.

Switch base station call screening on/off

m
d
1. Press
, scroll
to
ANSW MACHINE
and press
d
m
2. Scroll
to
ANSW SETTINGS
and press
d
m
3. Scroll
to
BS SCREENING
and press
.
u
d
4. Press
or
to select
ON
or OFF.
m
5. Press
to confirm.

Access answer machine menu via the Calls list

When the
is flashing to indicate new messages you can see caller details via
again to go to
ANSW MACHINE
to play new messages.
u
1. Press
,
CALL LIST
is displayed.
d
2. Press
,
ANSW MACHINE
is displayed.
m
3. Press
,
PLAY
is displayed.
m
4. Press
, the handset will start the new message playback. Once all messages are
played, the handset will return to standby.
NOTE
>
During message playback, press
anytime to return to standby.

Memory full

The memory is full if there is less than 15 seconds of recording time left or if the maximum total of
59 messages has been reached.
When the memory becomes full:
• The LED will flash quickly.
•
flashes quickly on the handset display.
• The machine will automatically switch to Answer Only mode.
If the memory becomes full while a caller is leaving a message, they will hear a beep and the call
is ended.
Help
m
and press
.
.
m
.
.
u
or press

10. Help

Charging
The
icon is not scrolling when the handset is placed on the base
• Bad battery contact – move the handset slightly
• Dirty contact – Clean the battery contact with a cloth moistened with alcohol
• Battery is full – no need to charge
Calls
No dialling tone
• No power – check the connections. Reset the phone: unplug and plug back in the mains
• Batteries are empty – charge the batteries for at least 24 hours
• You are too far from the base – move closer to the base
• Wrong line cable – use the line cable provided
d
• Line adaptor (when needed) is not connected to the line cord – connect the line adaptor (when
needed) to the line cord
Poor audio quality
The base is too close to electrical appliances, reinforced concrete walls or metal doorframes –
move the base at least one metre away from any electrical appliances
The
icon is blinking
• Handset is not registered to the base – register the handset to the base
• You are too far from the base – move closer to the base
• Switch OFF the Eco mode.
No ring tone
• The ring tone is deactivated.
• Increase the volume.
Caller Line Identification (CLI) service does not work
Check your subscription with your network operator
Phonebook
A phonebook entry cannot be stored
The phonebook is full. Delete an entry to free memory
Display
No display
• Try recharging or replacing the batteries.
• Try disconnecting and connecting the base power supply.
• If LED is not lit up, then try disconnecting and connecting the base power supply.
Registration
Unable to register another handset
• Maximum number of 5 handsets has been reached.
• The display shows SEARCHING. You must unregister a handset in order to register a new one.
23