Motorola APX 7500 İletişim Kılavuzu - Sayfa 2

Radyo Motorola APX 7500 için çevrimiçi göz atın veya pdf İletişim Kılavuzu indirin. Motorola APX 7500 2 sayfaları. Multiband mobile radio
Ayrıca Motorola APX 7500 için: Broşür (8 sayfalar), Ürün Teknik Özellikleri (5 sayfalar)

Sayfayı Yazdır
Motorola APX 7500 İletişim Kılavuzu
LASD Motorola APX 7500 - 07 Control Head
Keypad Button presets:
Keypad buttons 0 thru 9, # and * can be user programmed to instantly move to any zone/channel in the radio with
a quick button press & release. Always set the "1" key to your "Dispatch" channel for ease of use.
Keypad Button presets programming:
Set the radio to the desired zone and channel.
Press and hold a keypad button on 0 - 9, * or # for 3 seconds, the radio will sound a short beep.
The chosen keypad button is now set for that channel
To use:
Quickly press & release the keypad button on 0 - 9, * or # to recall the pre-programmed channel.
Using the Keypad Button presets, you can switch the radio to other zones or channels quickly and easily.
Locking the keypad will prevent the use of Keypad button presets.
Dynamic Zone "DZ" is available only in the APX series portable and mobile radios with the "RED-15" or later program
What is a Dynamic Zone?
Dynamic Zone, allows users to program any radio channel in the radio, in any order, onto the DZ up to 16 slots.
This is useful, if you need to change zones and channels often. By pre-programming the DZ with your most used channels, you will
not need to change zones as often.
Multi band radios may have more than one Dynamic zone, (see the channel plan for multi band radios)
Dynamic Zone "DZ" APX 7000 radio
When programming a Dynamic Zone "DZ", turn the volume down.
Newly issued radios come with the DZ empty. A empty channel will read "Blank" and make the "Empty List" tone, until it is programmed.
Programming a DZ is much like programming the Scan channels, if you stop or take too long during the programming process,
the radio will revert back to the beginning.
Before programming the DZ, determine which channels you want and what order you want them in
(use your channel plan to help find what you need).
Programming should start with channel 1. Channel 1 should be your dispatch or home channel.
Example Dynamic Zone:
DZ slot
-
1
Ch name
-
SCC
(Zone where the
-
Z3
channel is actually located)
Dynamic Zone programming:
1. Press and release the Zone key,
2. While on the Dynamic Zone, press and release the "ZnPr" key
press and release the "Edit" key
3. Highlight the "List Selection", Press and release the "Sel" key,
release the "Sel" key
4. Using the up/dn arrow pad, highlight the desired channel you want to add to your DZ, press and release the "Sel" key
5. The radio will read "Channel Updated" and revert to the DZ showing the name of the channel you entered and
which DZ channel slot (1 - 16) it is on.
6. Repeat as needed.
13 September 2016
Communications Solutions 323-881-8033, JRH
A PDF of this can be found at http://intranet/intranet/bureaus/cfmb/communications/index.htm
Note: This information may change with out notice.
2
3
4
5
CivicCtr LCMC
CRTRT1 CUSTDY1 SIMPLX1 empty
Z11
Z13
Z14
Z13
using the ZnUp / ZnDn arrow pad, find Dynamic Zone "Dynamic 1" and press "Sel"
6
7
8
empty
Z3
arrow up/dn to the desired dynamic channel slot (1-16) &
a Zone list will appear, arrow to the desired zone, press and
9
10
Cont,, to 16
empty
empty
Cont,, to 16
Page 2 of 2