Motorola Professional CDM1550 LS+ Servis ve Kurulum Kılavuzu - Sayfa 5
Radyo Motorola Professional CDM1550 LS+ için çevrimiçi göz atın veya pdf Servis ve Kurulum Kılavuzu indirin. Motorola Professional CDM1550 LS+ 32 sayfaları. Cdm-series control station
Ayrıca Motorola Professional CDM1550 LS+ için: Talimat Kitapçığı (5 sayfalar)
CDM Control Station
Scope of Manual
This manual is intended for use by experienced technicians
familiar with similar types of equipment. It contains all ser-
vice information required for the equipment described and is
current as of the printing date. Changes which occur after the
printing date are incorporated by service manual revisions.
These revisions are added to the manuals as the engineering
changes are incorporated into the equipment.
How to Use This Manual
This manual contains introductory material such as model
charts and accessories, as well as sections that deal with spe-
cific service aspects of the CDM Control Station. Refer to the
Table of Contents for a general overview of the manual, or to
the "Overview" paragraph in each section for a specific over-
view of the information in that section.
Other Documentation
Table 1 lists other documentation you may need to setup and
configure the Control Station.
Table 1. Other Documentations
Information
CDM-Series
CDM750 User Guide (6881091C54)
Operation
CDM1250 User Guide (6881091C55)
(North America)
CDM1550 User Guide (6881091C56)
CDM-Series
CDM-Series CPS HVN9025
Programming
(North America)
CDM-Series Service
Basic Service Manual (6881091C62)
(North America)
Detailed Service Manual
(6881091C63)
Technical Support and Service
For Technical Support, please call:
Motorola Inc.
(800) 927-2744
If it is necessary to return a unit for repair or replacement, the
call-taker will issue a Return Material Authorization (RMA)
number. Include the RMA number in the package with the
defective unit.
For information on warranty service, returns or repairs,
contact:
Motorola Inc.
Radio Support Center
2204 Galvin Dr.
Elgin, IL 60123
(800) 227-6772
To order parts, contact:
Motorola Inc.
2200 Galvin Drive
Elgin, IL 60123
(800) 422-4210
October, 2004
Location
6880309N15-A
Regulatory Requirements
In the United States, the FCC regulates licensing of RF frequen-
cies. The terms of the FCC radio license for a particular opera-
tion will determine the frequencies, output power, and antenna
height(s) for a given situation. The applicable "Part" of the FCC
Rules and Regulations must be consulted before a CDM Con-
trol Station is activated. In countries other than the United
States, contact the local government for licensing rules.
NOTE
In the United States of America, the CDM-
Series radios may not legally be used as the
transmit radio in a UHF (450 to 512 MHz)
repeater or base station application with 12.5
kHz channel spacing. The ±2.5-ppm fre-
quency stability capability of the radio does
not meet the requirements of part 90 of the
Rules and Regulations of the Federal Com-
munications Commission (FCC). In other
countries, check local frequency stability
requirements before placing a CDM-Series
radio based repeater or base station in opera-
tion.
Product Safety and RF Exposure
Compliance
Before using this product, read the
operating instructions for safe usage
!
contained in the Product Safety and
RF Exposure booklet enclosed with
C a u t i o n
your radio.
ATTENTION!
This radio is restricted to occupational use only to satisfy
FCC RF energy exposure requirements. Before using this
product, read the RF energy awareness information and oper-
ating instructions in the Product Safety and RF Exposure
booklet enclosed with your radio (Motorola Publication part
number 68P81095C99) to ensure compliance with RF energy
exposure limits.
For a list of Motorola-approved antennas, batteries, and other
accessories, visit the following web site which lists approved
accessories: http://www.motorola.com/cgiss/index.shtml.
Electrostatic Discharge – Sensitive
Parts
This product contains CMOS and other circuit components
which may be damaged by electrostatic discharge. Proper pre-
caution must be taken when handling circuit modules. As a min-
imum, grounded wrist straps should be used at all times when
the control station cover is removed and in the handling of cir-
cuit modules.
See section 11.9 of the Motorola R56-Standards and Guidelines
for Communications Sites for more detailed information.
Foreword
Scope of Manual
iii