Epson 1280 - Stylus Photo Color Inkjet Printer Kurulum Talimatları Kılavuzu - Sayfa 5

Yazılım Epson 1280 - Stylus Photo Color Inkjet Printer için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Epson 1280 - Stylus Photo Color Inkjet Printer 8 sayfaları. Product support bulletin(s)
Ayrıca Epson 1280 - Stylus Photo Color Inkjet Printer için: Kartuşların Değiştirilmesi (2 sayfalar), Ürün Destek Bülteni (6 sayfalar), Ürün Destek Bülteni (1 sayfalar), Tamamlayıcı Kılavuz (1 sayfalar), Kullanıcı Kılavuzu (27 sayfalar), Uyumluluk Kılavuzu (1 sayfalar), Tamamlayıcı Kılavuz (2 sayfalar), Buradan başlayın (2 sayfalar), Broşür ve Teknik Özellikler (2 sayfalar), Ürün Bilgileri (13 sayfalar), Buradan Başlayın Kılavuzu (6 sayfalar), Teknik Özellikler (2 sayfalar), Kullanıcı Kılavuzu (12 sayfalar), Ürün Destek Bülteni (3 sayfalar), Ürün Destek Bülteni (2 sayfalar), Ürün Destek Bülteni (4 sayfalar), Ürün Destek Bülteni (7 sayfalar), Başlangıç Kılavuzu (32 sayfalar)

6. Clean the right section of the printer housing with alcohol, then install the second

bracket on the right hand edge of the housing so the tubing is in a straight line. Put

the tubing into this small bracket. Now you are ready to insert the tubes into the

bottles. The position of the bracket opening can be either up or down. It does not

matter.

7. Next, you must install the Tube Guide onto the cartridge carriage. The Tube Guide

is installed on the side of the carriage that has the black cartridge. Clean the area

where the tube guide is to be installed with a small amount of alcohol. The bracket

is installed in such a way that the edge of the bracket is 1/8 of an inch from the

black cartridge on the left side and front. The Tube Guide position should be as

shown in the picture below.

After installation, check to be sure that the Tube Guide does not hit the left hand

side of the printer housing when the carriage is all of the way to the left side of

the printer. Since this dimension is very close it is best to check this by sliding a

business card between the Tube Guide and the printer housing with the carriage

moved all of the way to the left. If the business card slides freely between the

tube guide and the printer housing, it is installed correctly.

Set up the Bottles and Connect the Tubes:

The Spongeless CFS System that you have been shipped contains a set of our new bottle

caps with fittings. It also has white plugs on the tube ends that were not there before.

The installation of the tubes is as follows.

8. Once the tubes have the slack adjusted properly and they are securely inserted

into the Bridge Bracket clip, let the remaining tube length feed thru the beige clip

on the right hand edge of the printer. Close the clamp on the tubing. This will leave

the remaining tube length at the right side of the printer ready to be trimmed for

connection to the bottle tops.

S a v e

M o n e y

MIS Associates Inc

http://www.inksupply.com

a n d

I m p r o v e

2901 Auburn Rd

Fax: 248-289-6013

Y o u r

Auburn Hills, MI 48326

P r i n t i n g

800-445-8296