Toshiba 13P ASG -T Kurulum Kılavuzu - Sayfa 6

Klima Toshiba 13P ASG -T için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Toshiba 13P ASG -T 28 sayfaları.

Sayfayı Yazdır

Installation Place

A place w ic provides t e spaces around t e indoor unit as s own in t e
diagram
A place w ere t ere are no obstacles near t e air inlet and outlet
A place w ic allows easy installation of t e piping to t e outdoor unit
A place w ic allows t e front panel to be opened
CAU I N
Direct sunlig t to t e indoor unit s wireless receiver s ould be avoided.
T e microprocessor in t e indoor unit s ould not be too close to RF
noise sources.
For details see t e owner s manual.
emote control
A place w ere t ere are no obstacles suc as a curtain t at may block t e
signal from t e indoor unit
Do not install t e remote control in a place exposed to direct sunlig t or
close to a eating source suc as a stove.
eep t e remote control at least 1 m apart from t e nearest T set or
stereo e uipment. T is is necessary to prevent image disturbances or
noise interference.
T e location of t e remote control s ould be determined as s own below.
Side view
Remote
Reception
control
range
C ttin a ole and
Installation Plate
C ttin a hole
W en installing t e refrigerant pipes from t e rear
T e center of t e pipe ole
is above t e arrow.
1. After determining t e pipe ole position on t e mounting plate
t e pipe ole
65 mm at a slig t downward slant to t e outdoor side.
N
W en drilling a wall t at contains a metal lat wire lat or metal plate be sure
to use a pipe ole brim ring sold separately.
o ntin the installation late
Hook
Pipe ole
T read

Indoor unit

INDOOR UNIT
INDOOR UNIT
Top view
Indoor unit
Remote
control
o ntin
Pipe ole
65 mm
120 mm
Æ
65
103
Hook
1
Installation
Hook
plate
Pipe ole
Weig t
6
Mounting screw
hen the installation late is directl mo nted
on the all
1. Securely fi t t e installation plate onto t e wall by screwing it in t e upper and
lower parts to ook up t e indoor unit.
2. To mount t e installation plate on a concrete wall wit anc or bolts use t e
anc or bolt oles as illustrated in t e below fi gure.
3. Install t e installation plate ori ontally in t e wall.
CAU I N
W en installing t e installation plate wit a mounting screw do not use t e
anc or bolt oles. Ot erwise t e unit may fall down and result in personal
in ury and property damage.
Installation plate
eep ori ontal direction.
5 mm dia. ole
Clip anc or
local parts
CAU I N
Failure to fi rmly install t e unit may result in personal in ury and property
damage if t e unit falls.
In case of block brick concrete or similar type walls make 5 mm dia. oles
in t e wall.
Insert clip anc ors for appropriate mounting screws 6.
N
Secure four corners and lower parts of t e installation plate wit 4 to 6
mounting screws to install it.
Pi in and rain ose Installation
Pi in and drain hose ormin
Since dewing results in a mac ine trouble make sure to insulate bot
connecting pipes. Use polyet ylene foam as insulating material.
Rear rig t
Rear left
Bottom left
drill
Left
Bottom rig t
Rig t
.
ie c ttin bac bod slit
Cut out t e slit on t e left or rig t side of t e back body for t e left or rig t
connection and t e slit on t e bottom left or rig t side of t e back body
for t e bottom left or rig t connection wit a pair of nippers.
. Chan in drain hose
For leftward connection bottom-leftward connection and rearleftward
connection s piping it is necessary to c ange t e drain ose and drain
cap.
4
Anc or bolt
Pro ection
15 mm or less
6
Mounting screw
4 x 25R